0–10 V control
A named control family can use a separate brightness signal as well as a power-switching job. Exact equipment instructions establish the actual arrangement.
Understand the words.
Ask a better question.
1257 terms connected to real lessons. Definitions stay with their context: a technical term alone is not a diagnosis, design or legal conclusion.
1257 terms
Acceptance basis
The applicable design, manufacturer, contract or local requirement used to interpret the stated result.
Acceptance record
The applicable authority’s documented process outcome for a defined scope; its name and assessment method must be confirmed.
Access limitation
An area or assessment method that was unavailable or excluded during a particular visit.
A part or task left unchecked because it could not be safely reached or was outside the agreed work.
A stated restriction on what could be examined. It leaves a bounded information gap.
Access need
A household-defined requirement for an activity or route.
Access protection
The connected barrier, gate, door or cover arrangement intended to restrict unintended or unsupervised access to the water.
Access route
The ordinary sequence by which a child may reach an object or opening.
Accessible-ready
Planned for future accessibility adaptation under the identified standard’s scope; it does not establish present suitability for every household.
Documented provisions supporting future adaptation within a defined standard scope.
Accessory building
A building whose permitted relationship to the principal use is authority-specific.
Account holder
The authorized party identified for the actual billing arrangement.
Acquisition cash
Money used or still needed to complete the purchase and agreed setup, reconciled to actual credits, documents and due dates.
Acquisition cash plan
The dated plan including the deposit, investigations, completion funds and other identified purchase expenses.
Action
The requested supported response after the rule’s required evaluation.
Activity brief
The household’s agreed tasks, circumstances, preferences and unresolved individual needs.
Actuator
The mechanism operating a compatible control valve; distinct from a circulator moving fluid.
The part that moves a valve or another mechanism in response to its control.
The controlled part that changes a physical state; a lamp control is a convenience example.
Additional living expenses
Coverage for defined extra living costs following the relevant insured loss, within policy terms.
Adjustable-payment mortgage
A variable-rate arrangement whose payment changes under the lender’s stated calculation method.
Adjustment
Professional treatment of a relevant difference, supported by evidence.
Administrative authority
The legitimate account role able to manage the actual device or system permissions.
Adsorption
Attachment of selected substances to a surface, such as activated carbon, as water contacts it.
Affected assembly
Connected finish and concealed layers considered in the assessment of a water event.
Affected materials
The cabinet, wall, floor or other materials reached by water, beyond the source component itself.
Agreement transfer
The applicable process for another person to take on identified rights and obligations.
Air barrier
The connected materials and sealed joints intended to limit air moving through the building enclosure.
Air cushion
Compressed air that can expand as stored water is delivered from a pressure tank.
Air gap
Physical separation through open air between a supply outlet and the receiving water arrangement.
Air-and-dirt route
The connected floor tool, hose, wall inlet and pipes that carry air and dry dirt to the collection unit.
Air-control boundary
The connected parts intended to limit air leakage through the enclosure.
Air-control continuity
How the identified system connects across surfaces, edges and openings to limit unintended air movement.
The connected arrangement limiting air leakage across panels, joints, interfaces and penetrations.
Airborne sound
Sound beginning as pressure variations in air, such as speech, which can excite building surfaces or pass through openings.
Alarm interconnection
A compatible installed arrangement that allows a warning initiated by one device to activate other specified devices; distinct from their power source.
Alarm panel or hub
Equipment that receives and interprets relevant device events under its configured arrangement.
Allocation
The assignment of use to a space under the applicable arrangement; its duration and transfer need confirmation.
Alteration scope
The identified equipment, locations and work included in a particular electrical change.
Alternator
The generator component that converts engine-driven rotation into electrical output.
The generator component that uses mechanical rotation to produce alternating electrical output.
Amortization
The estimated time to repay the debt under the repayment assumptions.
Anchorage
The identified connection of the building to its supporting arrangement, with its actual design and installed condition requiring appropriate evidence.
The assembly transferring tendon force into the concrete at its anchorage location.
Anode
A sacrificial component used in applicable storage designs to help reduce tank corrosion.
Apparent power
An electrical quantity expressed in volt-amperes; it must not be silently substituted for real power in watts.
Appliance check scope
The question, operating conditions, accessible extent, date and limitations of an actual installation or service check; not permanent whole-system clearance.
Appliance cooling fan
A separately identified fan managing appliance heat; the named Bosch example can continue after cooking.
Appliance service scope
The exact unit, concern, functions, conditions, findings and exclusions addressed by a dated service assessment.
Application stage
The point recorded in a particular application process on the date checked. It does not promise construction.
Approval condition
A requirement attached to a particular decision. Ask separately whether it has been met and which next permission applies.
Approved building Fire Safety Plan
The building-specific plan residents obtain and learn through the responsible building team; a generic guide or household sketch is not its replacement.
Aquifer
Permeable geological material that stores groundwater and can yield a useful supply to wells or springs. A regional aquifer description does not establish one well’s supply or water quality.
Arrival route
The actual path from the chosen arrival point into the dwelling.
As-built elevation
A surveyed installed height at an identified location, reference and survey date.
As-built information
Information describing the completed arrangement, with its author, date and verification limits.
As-built record
A record intended to describe completed work. Its author, scope and method explain how much was actually observed.
A record describing what was actually installed, with its date and scope.
As-constructed drawing
A dated record of the completed arrangement within its stated scope; ask how it matches the design, changes and completion information.
Asphalt paving
Paving with aggregate and an asphalt binder, working with the supporting courses described by its actual assembly.
Assembly
The actual connected roof layers, structure and interfaces, rather than the visible covering alone.
Assembly continuity
The way the identified water-control arrangement connects through fields, seams, corners and penetrations; not a property finding from one surface view.
Assembly scope
The particular roof, ceiling and transition components evaluated in an assignment.
Assessed scope
The locations, components, purpose and methods covered by an assessment, including exclusions and sampling limits.
Assessed work proposal
The rooms, materials and intended work given to the assessor. Compare any later design change with that original plan.
Assessment boundary
The actual object, material, area and question covered by a professional’s finding.
Assessment coverage
The locations, methods, dates and questions included in the professional review, together with its exclusions.
The specific locations, access, methods and purposes included in a professional review.
Assessment dependency
An answer or condition needed before another professional task or household decision can be evaluated.
Assessment extent
The components, locations and methods actually included in an agreed review, kept with its access restrictions and exclusions.
The locations, applications, methods and access limits actually covered by the professional engagement.
Assessment scope
The specific question, areas, methods, access, records and limits agreed for a professional assessment.
The parts, routes, conditions and methods included in a provider’s stated investigation, with its exclusions.
The purpose, locations, methods, conditions and exclusions attached to a professional conclusion.
Assignment
A transfer requiring the actual agreement and applicable approvals.
A proposed transfer under the actual consent, terms and legal advice.
Assistive alerting channel
A visual, vibrating or other suitable warning method considered with the person’s needs and actual compatible equipment, without guaranteed waking.
Associated equipment agreement
The separate system-equipment agreement in the Ontario retailer example. Read its own terms with the associated electricity agreement.
ASTC
Apparent sound transmission class: an airborne rating that accounts for direct and relevant flanking contributions between spaces, with prediction and measurement kept distinct.
Attendance
An accepted human visit role, distinct from monitoring or a technical inspection.
Attractant
A condition such as accessible food or water that may support activity; it does not identify an animal or establish the cause by itself.
Attribute
A feature identified for its heritage significance in the relevant record.
Attributed account
A statement linked to the person who supplied it, kept separate from a professional finding.
Attributed date
A date kept with the person or document that supplied it, rather than treated as independent certification.
Attributed history
Information recorded with the identity of who supplied it, without silently treating it as independently verified.
Attribution
Explaining what caused a change. An upgrade occurring between two bills does not isolate its contribution.
Auger
The front spiral assembly that gathers snow toward the centre in the illustrated two-stage arrangement.
Authorized reliance
Permitted use of a report under its actual engagement.
Authorized supplier request
An enquiry made by the account holder or someone properly allowed to act for them; a house viewing does not provide that authority.
Authorized use
The use permitted for the appraisal service through its engagement.
Authorized user
A party identified and authorized for the appraisal engagement; receiving a forwarded copy does not establish that status.
Automatic defrost water
Water handled after the named automatic defrost function; the example manual describes a channel-to-tray and evaporation relationship.
Automatic transfer equipment
The installed arrangement that selects the appropriate source for connected loads and prevents unwanted feedback between sources.
Averaging window
The time interval and included data used to produce a reported average.
Backfeed
Electrical power taking an unintended route into utility or other wiring, with serious danger to people.
Backflow
Unwanted reverse movement through a connection toward a drinking-water system, distinct from reverse wastewater flow.
Water movement opposite the intended normal direction.
Backflow protection
An arrangement addressing reversal risks at actual cross-connections, distinct from drainage backwater protection.
Backhaul
The return connection from an additional network point toward the primary network route.
Backpressure
A reverse-flow concern when a connected downstream system has higher pressure than its supplying side.
Backsiphonage
A reverse-flow concern associated with reduced pressure on the supplying side of a connected arrangement.
Backup power capability
The actual installed arrangement’s ability to supply stated loads during an outage, subject to its power, energy, operating and connection limits.
Backup reserve
A model-specific allocation for backup operation. Obtain the actual manufacturer explanation; a setting alone does not establish charge at an outage.
Backup-load schedule
A dated list of confirmed supplied, managed and excluded equipment and relevant dependencies.
Backwater valve
A device on an identified wastewater drain route that helps limit reverse flow from its receiving system.
Balancing
Checking and adjusting the specified relationship between supply and exhaust airflows in a defined operating condition.
Barrier screen
A model-specific protective barrier intended to reduce burn risk from contact with hot glass; it does not make the glass cool.
Base and subgrade
The base is a supporting pavement layer. Subgrade names the ground prepared to support the pavement.
Baseline
A dated starting record of known conditions and evidence, not a guarantee of future performance.
Basin vent
The identified air connection serving the changing air space above collected wastewater.
Battery compartment
The machine’s protected place for the intended removable packs.
Battery pack
The enclosed battery assembly that stores energy for the identified device.
Battery-backed outlet
A model-identified output supported by the UPS battery within its limits.
Beam
A member spanning a space and carrying supported loads toward its bearings at walls, posts or other designed supports.
Bearing
The supporting contact through which a member passes load. Its material, extent, connection and adequacy need actual evidence.
Bedding
The layer immediately below segmental paving units; distinct from the supporting base below it.
Below-grade assembly
The connected foundation, floor and associated layers interacting with ground and indoor conditions.
Billing context
The dates, readings, rates, household changes and conditions needed to understand a utility comparison.
Billing period
The stated interval associated with a billed quantity or charge, separate from the issue and payment due dates.
Blade control
A model-specific control affecting the cutting system or engine/motor, distinct from ground drive.
Boil-water advisory
A notice directing the specified boiling or alternative-water response to a microbial concern.
Bonded finish
A finish with a specified adhesive relationship to its receiving substrate; this does not identify every concealed layer or its condition.
Bonded tendon
A tendon arrangement in which the steel is bonded to the surrounding concrete, commonly through grouted duct construction.
Bonded waterproofing membrane
Water-control material bonded to a substrate close behind the tile in the identified system, with separate requirements at its junctions.
Bonding
The protective electrical connection that must be identified and assessed by the qualified professional.
Bonding flange
A drain interface designed for connection to a compatible bonded waterproofing membrane; distinct from the visible grate and the waste outlet.
Braced wall panel
A physical wall portion designed and installed to resist sideways forces in its applicable structural system.
Branch circuit
The circuit wiring and protection supplying particular outlets, lights or equipment downstream of distribution equipment.
A circuit distributing electricity to specified equipment or outlets downstream of its protection.
The circuit wiring serving particular connected loads beyond the distribution equipment.
Brick core
The heat-storing material within the protected cabinet; its stored thermal energy changes with charging and release.
Bridge proposal
Temporary finance under the actual provider’s approval and terms.
Brown coat
The second base coat in that example, building and levelling the surface before finishing.
Brush seal
A weather seal using flexible fibres at an appropriate sliding or moving interface.
Building drain
The drainage route collecting connected wastewater inside the building before it continues towards the building sewer.
Building enclosure
The surrounding roof, walls, lower enclosure, windows and doors that separate indoor space from outdoor conditions.
Built form
The physical arrangement of homes and their connections, considered separately from the legal ownership interest.
Burner
The part where supplied gas burns with air to produce heat.
Busbar
A conducting part that distributes electrical current to the heating portions of the illustrated film product.
Buyout quotation
A dated price and terms for buying the identified existing equipment; it is not a new appliance installation quote.
Bylaws or rules
The actual governance documents and amendments describing how the organization operates.
Bypass
An unintended route that can allow air to avoid the assessed filter media; a real share requires evidence.
Bypass humidifier air route
The documented branch through the humidifier between warm-air and return-air sides.
Cabinet box
The storage frame, distinct from its moving front and decorative finish.
Calibration context
The reference, conditions and method supporting a stated measurement relationship.
Candidate path
A possible air connection considered in investigation, distinct from a verified route.
Canopy
The cover near the ceiling; its appearance does not reveal or approve concealed support.
Cantilever
A projecting member or assembly whose continuation transfers forces into supporting construction.
A member or slab projecting beyond its support, transferring its relevant forces back into supporting construction.
Capacity
A rate of useful heat delivery or removal at stated conditions, commonly expressed in kW of heat.
Capillary action
Liquid water moving through narrow spaces or porous materials, including sideways or upward; often called wicking.
Capillary break
A separation interrupting direct liquid-water contact between materials.
Capillary moisture
Water movement through connected small pores in a material; its possibility does not identify the source of one damp patch.
Capture performance
How effectively the arrangement collects source-bearing air, a different question from fan airflow alone.
Carbon exhaustion
Loss of available capacity for the carbon’s intended adsorption task, which can occur while water still passes through.
Carbon monoxide
A hazardous gas associated with incomplete fuel combustion.
Caregiver handoff
An explicit agreement about responsibility and current unresolved household concerns.
Carrier mesh
The open supporting material that holds the heating cable in the illustrated mat; not itself a metal heating element.
Cash timing
When money is actually available compared with when external payments are due.
Catchment
The area contributing water to a particular route or location.
The identified surface contributing runoff to the collection route.
Cation exchange
A process in which positively charged ions in the water exchange with ions held on a treatment medium.
Cavity
The intended food space, distinct from closed electrical compartments.
Cavity convection
Fan-driven circulation within the named oven cavity, separate from appliance cooling and kitchen exhaust.
CEER
Combined energy efficiency ratio: a rating distinct from cooling capacity.
Ceiling fan
A suspended appliance whose rotating blades circulate air; it is different from a ducted exhaust fan.
Certification scope
The particular product and requirements covered by a certification mark or document. Ask what it evaluates separately from this home’s installation.
Certified claim
A particular performance claim verified within the applicable standard and exact product listing, without expanding it to all water-quality questions.
Certified reduction claim
A claim verified for an exact device and relevant standard/test conditions, distinguished from the standard number or another product’s claim.
Change order
A documented change to the agreed work, with the actual approval and cost or timing effects described.
Change process
The agreed way to assess, authorize and record altered work under the actual contract.
Change record
A written record of a revised scope or decision, preserving the reason, location and applicable responsibilities.
Changed-use boundary
The construction interface that must be understood when the intended uses on either side change.
Changeover regulator
A regulator product family associated with changing between supplies; the actual arrangement and owner instructions must be identified by its provider.
Charge control
The arrangement that determines replenishment of the heat store, separate from the room’s immediate demand.
Charger
Equipment intended to put energy back into the matching battery.
Charging status
A model-specific indication of the charging process, not a complete condition assessment.
Charging window
The time during which the vehicle is available for charging before it is needed.
Child-resistant
Packaging intended to impede access, not a claim that a child cannot open it.
Chronology gap
An event’s date or relationship to other events is unknown; preserve that gap rather than inventing a sequence.
Chute
The discharge passage that swivels to change horizontal direction.
Chute deflector
The outlet component that changes discharge elevation, distinct from rotating the chute horizontally.
Circulating blower
The fan that moves household air through the equipment and connected distribution system.
The fan supporting household-air movement in the named furnace arrangement, distinct from its combustion air inducer.
Circulation
Movement between the rooms and activities the household uses.
Circulation pump
A pump that moves water through the pool or hot-tub system.
Circulator
A pump moving water around its designed route; motor operation alone does not prove useful delivery.
A pump intended to move water around the relevant circuit.
Cladding
The exterior-facing material; it is one part of the enclosure assembly.
Class K
The CCOHS category for combustible cooking oils or fats in cooking appliances; not implied by an ABC marking.
Clean-air delivery
The effective flow of particle-cleaned air associated with a device and specified operating conditions.
The effective rate of particle-cleaned air supplied by a device under stated conditions.
Cleaner-air space
A place managed to reduce smoke exposure while considering other indoor conditions; it is not a universal safe-air guarantee.
Cleanout
An opening provided for professional access to the drainage route; its location and the pipe it serves need identification.
Climate normal
A statistical summary for a defined historical period and observation location.
Closed-cell structure
A material description with largely enclosed cells; colour or texture alone cannot establish classification or performance.
Closeout index
A guide to the actual final records, drawings, warranties, manuals and unresolved items for a defined project.
Closing adjustment
An identified allocation or credit between parties under the actual transaction and supporting records.
Closing-funds reconciliation
The explanation connecting price, credits, actual available financing, adjustments and separately included charges to the remaining buyer funds.
Cloud dependency
A required outside service whose availability is distinct from the local network.
CO shutoff
A generator protective function responding near its sensor; it does not certify indoor air or an acceptable site.
Co-operative organization
The legal organization through which members provide and govern housing under its actual framework.
CO2-equivalent output
An inferred output labelled by a manufacturer; it must not be assumed to be a direct measurement of carbon dioxide.
Coating history
Known product, date, surfaces and preparation recorded for finish work.
Coincident demand
Demand from loads operating together at a relevant assessed supply boundary.
Collateral charge
A registered security arrangement that may secure additional borrowing with the lender; the registered amount differs from the actual debt.
Collection account
An existing water observation kept with its period, known destination and ordinary context, without inventing missing measurements.
Collection basin
The container receiving connected-fixture wastewater before the pump moves it onward.
Combination alarm
An identified device containing more than one stated hazard-detection function, which retain their own instructions and response meanings.
Combustion air
Air serving the operation and venting requirements of an identified fuel-burning arrangement.
Air used by the fire. Its source is distinct from air circulating around the room.
Combustion air inducer
A separately identified fan in the named model’s documented combustion-and-vent operation, rather than proof of household airflow or completed safe operation.
Comfort observation
A person’s dated experience at a stated location, different from an instrument result or heat-safety finding.
Command control
An identified wall control, remote, keypad or app that requests operation; issuing a command does not establish clearance or protective performance.
Commanded mode
The operation requested by the control, distinct from independently verified equipment response.
Commencement evidence
The property-specific document or verified event establishing the start of the applicable coverage, under its actual rules.
Commissioning
Verifying the installed equipment, controls and measured performance against the applicable design and instructions.
A documented process that checks and establishes an installed system’s operation against its intended requirements; the actual scope and measurements matter.
Professional verification and handover of the delivered installation against its intended functions and applicable instructions.
The relevant provider’s scoped process and evidence for putting the actual installed system into intended service.
Defined verification of an installed arrangement under recorded conditions and scope.
Commissioning evidence
A record of specified equipment or system checks under identified conditions.
Recorded checks of installed work within their actual method, locations and conditions.
Commissioning record
Evidence identifying what installed-system verification occurred, its conditions, findings and interpretation.
The identified installation and functions actually demonstrated, with method, conditions and remaining limits.
Commissioning scope
The identified completed-work checks, equipment, conditions and results in a professional commissioning record.
Common aisle
A shared route connecting parking spaces, entry and other destinations; access and work arrangements need enquiry.
Common element
A component addressed through the applicable condominium or shared-property arrangements rather than assumed to be within one owner’s private scope.
Common elements
The shared property defined by the actual condominium documents.
Common route
An established supply segment shared by the demands being considered.
Common service access
An identified access arrangement for shared equipment and service spaces, with actual privacy and legal responsibilities confirmed.
Common-system boundary
The documented division of shared and individual infrastructure and responsibilities.
Comparable sale
A transaction used as evidence for the subject’s defined value enquiry.
Comparison boundary
The equipment, energy sources, period, units, conditions and charges included in a stated comparison.
Comparison horizon
The same stated end date used to compare payments, charges and remaining balances.
Compartment air distribution
Movement of cold air around stored contents, distinct from heat transport by refrigerant. The actual hidden path remains model-specific.
Compatibility
Whether identified products are designed to work together under their documented conditions. It is different from approval or an assessment of present connections.
Whether the exact device, battery and charger are intended to work together.
Compatible repair
Opening work that addresses the supported access concern while preserving the actual building and equipment functions.
Completion
The property transaction stage whose requirements the legal professional explains.
Completion adjustment
A transaction allocation explained by the legal professional from the agreement and records.
Completion evidence
Documents describing what defined work was completed and what follow-up or verification actually covered.
The specified record or assessment of what was delivered and checked, retaining its limits.
Records addressing what was installed or repaired and how the promised result was checked; distinguish them from proposal and payment records.
Records connecting authorized scope with the actual performed work.
Completion statement
An author’s finding within a defined engagement and scope.
Compliance review
The municipal review described by the actual authority, with its stated scope and exclusions.
Component-specific task
Work recorded for a named part, such as a filter replacement; it does not describe every other part’s condition.
Composite action
Materials working together through their connection rather than performing as unrelated layers.
Compression
A pushing-together force or stress; the concrete and overall design must be assessed in their actual context.
Compression seal
A seal designed to make contact under appropriate closed-position compression.
Compressor
The machine that compresses refrigerant vapour and raises its pressure and temperature using electrical work.
A component that compresses refrigerant gas and raises its temperature in the abstract mechanism; this term does not identify cabinet position or service condition.
Concealed condition
A condition hidden from the available assessment; its existence or consequence should not be invented.
Concealed limitation
A relevant part that the stated assessment could not see or establish.
Concealed route
A plumbing route not accessible within the stated assessment; its material and condition remain separately qualified.
Concealed sprinkler cover
A model-specific cover assembly hiding parts of a sprinkler; appearance alone establishes neither the model nor correct assembly.
Concealed work
Construction no longer visible without appropriate access.
Conciliation
A distinct step within a relevant dispute or warranty process; the applicable administrator’s current procedure and dates determine what is required.
Concrete
A construction material combining cement, water and aggregates. Cement is its binder, not another name for the complete paving.
Concrete core
The structural concrete portion within the actual designed wall.
Concrete cover
The concrete between embedded reinforcement and the surface; part of the steel’s surrounding protection.
Condensate
Liquid water formed when water vapour cools onto a sufficiently cold surface.
Liquid collected when water vapour condenses; it needs its intended drainage route.
Liquid water formed when airborne water vapour condenses on a cooled surface.
Liquid water formed from air moisture on a sufficiently cold surface under the operating conditions.
Collected liquid associated with moisture in a compressed-air system; its composition and disposal need actual context.
Condensation
Water vapour changing into liquid at a surface cold enough for that change under the surrounding conditions.
Water vapour becoming liquid water on a sufficiently cold surface. In colder conditions, moisture can appear as frost.
Condensation drying
A named drying process in which chamber moisture forms droplets on interior surfaces and can run off; not a universal explanation for standing or escaped water.
Condenser
The exchanger’s heat-releasing role: refrigerant transfers heat away and condenses into liquid.
The heat exchanger where refrigerant gives up heat to the water in this heating explanation.
The hot-side heat exchanger where refrigerant rejects heat to its receiving air route.
Condition
A configured restriction evaluated under the platform’s stated logic.
The actual technical state, distinct from protected status.
Condition date
The date defining physical characteristics used by the relevant assessment.
Condition deadline
The date or time attached to an agreed condition; ask how the actual contract handles the required action and notice.
Condition scope
What the technical provider actually examined and reported.
Conditional extrapolation
A calculation extending an observed average only if its assumed rate and duration continue to apply.
Conductor
The electrically conductive part carrying current; its insulating covering is a different material.
Conductor insulation
The wire’s own protective covering, separate from ceramic supports.
Configuration
The equipment, connections, controls and operating arrangement present when the check was performed.
The identified plumbing route and equipment relationships surrounding the exchanger.
Connection acceptance
The utility’s recorded acceptance of the described equipment and operating arrangement. Read its scope alongside later changes.
Conservation
A supported approach to sustaining the identified heritage value.
Constant-load scenario
An arithmetic example with known deliverable energy, constant power and no recharge; starting, running and transition compatibility are separate assumptions.
Constant-pressure operation
An identified control arrangement requiring a maintained command for travel; device-specific instructions establish its actual use.
Construction timeline
An identifiable sequence of work, inspections, occupancy and later changes.
Contact resistance
Resistance at an electrical interface that can contribute to local heating when current passes through it.
Contact reversal
An identified opener response to contact under its specified conditions, distinct from a photoelectric input and not tested by this guide.
Contact sensor
A device that reports a selected opening state, commonly through a sensor and magnet associated with a door or window.
Contact-plate method
The named below-subfloor arrangement in which the tubing and plate provide a contact heat-transfer route into the timber floor.
Contactor
An electrical switching component controlled by another part of the identified system.
Contacts
The connection points where the pack meets its tool or charger.
Contamination scope
The locations and materials considered in an assessment and cleaning plan for suspected rodent waste; distinct from choosing pest control.
Contracted scope
The work described by the executed contract and its applicable documents and changes.
Contributory value
A feature’s market contribution, distinct from its expenditure.
Control connection
A connection serving sensing or coordination, distinct from the power path supplying household loads.
Control continuity
Connection of the relevant air, moisture or thermal functions across an assembly.
Control indication
A model-defined displayed state or request; it does not independently measure equipment output or room heat delivery.
Control interlock
A designed relationship between control functions; behaviour must be learned from the actual model.
Control lock
A model-specific electronic-operation feature, distinct from physically locking the door.
Control zone
An area governed by a stated control relationship; its boundary need not equal one room or one water loop.
Control-layer continuity
How a particular function is maintained through changes in materials and at connections.
Controlled route
The water passage and downstream connections affected by the actual valve.
Convection
Heat transfer carried by moving air.
Heat carried by moving air; warmed air rising through a common baseboard is one example.
Heat transfer through moving air around warmer parts.
Cool-mist droplets
Tiny liquid droplets dispersed into air, distinct from gaseous water vapour.
Cooled coil
A cooled heat-transfer surface where some moisture in passing air can condense into liquid.
Cooling route
The intended movement of air that removes equipment heat, distinct from combustion exhaust.
Coordination
Connecting individual-use needs with building design, equipment and assigned technical responsibilities.
Coordination record
A working index that connects an issue with its reports, responsible contacts and remaining questions.
COP
Corresponding useful heat output divided by electrical input at a consistent stated condition, interval and boundary. The ratio has no unit.
Copper pigtail
A short copper conductor segment at a transition; the term alone does not establish removal of the upstream conductor or a suitable installed repair.
Corporation deductible
The retained portion under the corporation policy, distinct from a personal-policy deductible.
Costable scope
A task described clearly enough for a provider to price its stated work, assumptions, inclusions and exclusions.
Counterbalance
The matched spring and associated hardware arrangement that offsets door weight; stored energy makes adjustment and repair a qualified-service task.
Coverage evidence file
The address- and use-specific insurance response, declarations, selected forms, conditions and effective-arrangement confirmation.
Coverage response
The insurer’s actual written answer for the specific property and requested protection.
Critical-load schedule
A written list of priority jobs, their actual devices and circuits, and the dependencies the backup design must address.
Cross-connection
A connection that can allow water to move between routes intended to remain separate.
A permanent, temporary or potential link between drinking-water plumbing and another source or potential contaminant.
Crossover arrangement
A named product arrangement in which hot and cold distribution interact under its intended valve and controls; not a connection to improvise.
Culvert
A conduit carrying water through a crossing such as a driveway over a ditch.
Curb-stop
An outside valve used to isolate the incoming service under the local utility’s procedures. Arrange utility help rather than operating an unfamiliar outside cap.
Cured-in-place pipe (CIPP)
A lining method using an installed material cured in an existing pipe; the applicable design and completion requirements are project-specific.
Current sampled RH
The relative humidity represented at a sensor’s location and time. It is an air sample, not a measurement of water hidden in a wall.
Current title
A dated registry record identifying the owner and registered interests in the identified parcel.
Cut and fill
Removal or addition of ground material, changes that can require relevant design and local advice.
Cut-in
The factory pressure condition at which the named pressure switch restarts the motor.
Cut-out
The factory pressure condition at which the named pressure switch stops the motor.
Cutting assembly
The model-specific blade system and its intended mounting and driven components.
Cutting-height setting
A product adjustment related to deck support; not an exact measurement of every finished grass blade.
DAR
The named standard’s record of planned future-access provisions and related design information; it helps a later designer find the provisions but does not make the adaptation constructed or personally suitable.
Data version
The particular downloaded or published record, with its date and notes, retained so later changes can be reconciled.
Decision dependency
An answer you need before another plan can be assessed, such as resolving a material question before defining removal work.
Decision-critical gap
An unanswered question whose result could change an essential household use or purchase decision.
Decision-relevant measurement
A measurement whose possible results can change the next choice; ask which alternatives it can distinguish.
Deck
The surrounding mower structure related to cutting, material movement and containment.
Deck-mounted skylight
A unit mounted to the roof deck in its identified manufacturer’s arrangement.
Decommissioning record
A report describing how a named storage system was retired and which handling, removal, reporting and environmental tasks were included.
Dedicated return
A separate pipe route bringing circulating water back toward the heating source.
Dedicated ventilation ducts
Ducts serving the ventilation routes separately from central heating-air distribution.
Deductible
The amount the insured is responsible for under the applicable policy provisions, kept separate from the coverage limit.
Deductible responsibility
The actual legal/document enquiry about who bears a deductible for the event; not decided by its amount.
Deferred observation
A named question that could not be answered under the actual access, weather or completion conditions.
Deferred verification
A named assessment not yet performed under the required available conditions, kept separate from a failed finding.
Deficiency record
A dated description of an observed incomplete, damaged, missing or operating concern, with location and follow-up information.
Deflector
The hinged hood at the chute outlet that changes its tilt.
Defrost
A model-specific process that manages frost accumulation in cold operating conditions.
Defrost state
A model-specific protective operation addressing ice on the cold surface. In the named Danby example the compressor can stop while the fan continues.
Degree-day context
A temperature-and-time indicator using a stated base. It provides context for demand rather than measuring equipment efficiency.
Dehumidistat
A humidity-responsive control that can request ventilation when its measured humidity exceeds the selected threshold.
Deliverable scenario energy
The assumed energy available to the selected loads for a scenario, with the measurement point and any included allowances explained.
Delivery rate
Water supplied over a stated time under identified operating conditions, with the volume and time units retained.
Delivery ticket
A record of its stated fuel delivery transaction, separate from an installation or whole-system condition assessment.
Demand assumption
The described use on which an electrical assessment is based.
Demand-based control
The named controller’s use of water-consumption information to govern regeneration.
Dependency
Something a device needs for its job, such as available power or a usable discharge route.
A later decision or piece of work that relies on an earlier answer or outcome.
A supply or connection a function needs, such as power, a compatible communication link or a remote service.
Dependency map
A record linking a needed function to power, equipment, services, confirmed scope and a safe alternative.
Deposit credit
Money already paid under the agreement accounted for toward the transaction, rather than charged a second time.
Design elevation
An intended height at an identified location and reference in the applicable plan.
Designation
A formal status defined by the applicable actual records.
Device ownership transfer
The provider-supported process for changing a device’s account association, distinct from physical possession.
Device test
A bounded assessment of an identified protective device, distinct from water analysis or an entire hazard survey.
Diaphragm
A structural floor or roof assembly transferring forces across its plane to the resisting system.
Differential movement
Unequal movement between places or connected parts; actual significance needs structural and site context.
Parts changing dimensions or position differently, requiring the actual connection to be understood.
Differential pressure
The pressure difference between two points; an appropriately connected pressure indicator does not measure occupied-space radon concentration.
Dimmer
An ordinary lighting control that allows an adjustable light level when the documented lighting equipment supports its method.
Dip tube
An internal tube that carries incoming water low in the illustrated top-inlet tank arrangement.
Direct exchange
An arrangement in which refrigerant circulates through the ground-side tubing.
Direct vent
A design using outdoor combustion air and carrying combustion gases outdoors through its specified venting arrangement.
Direct/non-direct vent configuration
The named manual’s distinction in the source of combustion air while combustion products discharge outdoors; the applicable arrangement must be identified for the actual model and installation.
Dirt collection system
The bag, filters and container a particular unit uses to separate and hold collected dirt.
Disbursement
An identified expense incurred in carrying out a professional service, distinct from the professional fee itself.
Discharge
The applicable process to release registered mortgage security.
The appliance’s outgoing water/particle connection to receiving drainage.
Discharge check valve
A one-way device on the pump route that helps limit liquid returning down that discharge.
Discharge guard
A protective part associated with an intended outlet; not an optional cosmetic flap.
Discharge pipe
The route carrying wastewater away from the pump toward its identified connection.
Discharge valve
The intended onward route from that chamber during its delivery stage.
Disclosure
The relevant project information provided under the applicable framework.
Dishwasher circulation
The internal reuse of water through the washing process, kept distinct from household inlet delivery and outgoing discharge.
Dishwasher cycle context
The actual program, options, ordinary load and operating circumstances attached to an observation rather than a universal timer or performance finding.
Dishwasher detergent delivery
Introduction of the appropriate cleaning product into the intended part of the cycle, separate from merely having product in a compartment.
Dishwasher discharge
Water leaving the appliance’s internal process through its outgoing route toward the receiving building drainage.
Dishwasher filtration
Separation of soiling from water used in the washing process, with product-specific components and care instructions.
Dishwasher rinse aid
A product with a water-runoff role described by the manufacturer, distinct from the washing detergent and governed by matched instructions.
Dishwasher spray arm
An identified component distributing wash water over dishware in its designed arrangement; its appearance alone does not establish reach or operation.
Disinfection
Treatment that controls microorganisms in the water, using products and devices suited to the system.
Dispersal area
The part of an onsite arrangement that distributes effluent into its receiving environment, as identified in the actual system records.
Disposable extinguisher
A non-rechargeable unit with an intended replacement route after use.
Distance reference
The origin and direction used for a reported distance along the pipe; different references require reconciliation.
Distribution
The shared route carrying energy between connected locations.
Distribution assessment
A scoped evaluation of how conditioned air or heat reaches and leaves intended spaces.
Distribution path
The documented route by which an installed system delivers heat to a space, such as air ducts, room units or water-based emitters.
Distribution piping
The indoor supply branches carrying water to taps, appliances and other equipment. Drains carry used water away and do a different job.
Distribution system
The connected route carrying treated water toward users; indoor plumbing continues that route.
Distribution work
Work affecting how power is supplied within the building; it is not automatically a larger utility service.
Distributor trough
The upper part spreading incoming water across the pad.
Disturbance
Cutting, moving, damaging or removing material in a way that can release dust or fibres.
Do-not-consume advisory
A notice prohibiting consumption uses; boiling does not make it equivalent to a boil-water notice.
Do-not-use advisory
A broader notice restricting affected tap water from use, including contact where the incident requires it.
Documented completed scope
The defined work supported by the relevant completion records, preserving review limits and remaining items.
Domestic hot water
Water heated for uses such as bathing and washing, distinct from a space-heating enquiry.
Door gasket
The named sealing interface between door and cabinet; its presence is not a verified sealing or cooling result.
Door guidance
The identified roller, track and supporting arrangement that controls the moving door’s route; visible shapes do not establish alignment or capacity.
Door interlocks
Safety devices associated with the door; never an owner test or bypass.
Door keeper
A receiving component for the identified sliding-door lock; its role and adjustment differ from a hinged-door assembly.
Door leaf
The moving door panel or slab, distinct from its stationary frame and surrounding wall.
Door threshold
The lower crossing associated with the door system; its visible surface does not reveal all underlying support or water-control construction.
Door weatherstrip
A product-specific contact component at a moving door joint; suitable contact is distinct from a fixed wall-interface seal.
Double-leaf assembly
An assembly with two surface leaves and a space between them; panel mass, enclosed air and support connections interact acoustically.
Downstream
On the delivery side of a component, such as the controlled supply leaving a regulator.
Draft
The pressure difference that moves smoke and gases through a chimney or venting route; its behaviour depends on the actual equipment and conditions.
Drain pan
The part collecting liquid left over from the pad process.
Drain stack
A vertical sanitary drainage pipe receiving connected discharge through one or more storeys.
Drain, waste and vent (DWV)
The connected wastewater and air arrangements that remove discharge and help protect trap seals.
Drainage
A route that lets free liquid water move out of the wall.
Routes that direct water away under the actual design.
Drainage and drying
Different moisture questions: mobile water leaving an assembly and moisture held in materials being released under relevant conditions.
Drainage plane
The surface or level intended to carry water toward outlets. It may be below the visible walking finish.
Drainage route
The connected collection, conveyance and discharge arrangement, with the actual destination and maintenance/access questions retained.
Drawdown
The reduction in water level during pumping, interpreted with rate, duration and recovery data.
Drawing revision
An identified version of a drawing. Ask which version relates to the approval and completed work.
Drinking-water advisory
An official public-health message restricting water use while a real or potential concern is addressed.
Driver or power supply
Electronics that manage power for the documented LED lighting system. The actual location, output and serviceability depend on the equipment.
Driveway crossing
Calgary’s term for the connection where a private driveway accesses a public road, potentially through sidewalk, boulevard or curb context. Other authorities have their own terminology and process.
Dry chemical
An extinguishing powder; it is distinct from the gas that provides discharge energy.
Drying
Removal of moisture remaining in or on materials after free water has drained.
Drying potential
The ways an assembly can release moisture under its relevant material and environmental conditions.
Drying record
Dated material and location information, methods and interpretation explaining the assessed drying progress or conclusion.
Evidence of particular measurements and decisions, with methods and limits.
Drying shrinkage
A moisture-related reduction in hardened concrete’s dimensions; it is a mechanism, not a diagnosis of this line.
Dusting
Concrete powdering at the wearing surface, when an actual assessment establishes that the technical term fits.
Duty cycle
The manufacturer’s permitted or recommended operating pattern under stated conditions, not a universal continuous-use promise.
Dwelling supply isolation
An identified arrangement for interrupting supply to one area while considering the other area’s service.
Earmarked balance
Money you still hold for a stated purpose. Moving it between your own accounts is an internal transfer, not payment for completed work.
Edge restraint
A perimeter element with the job of limiting horizontal movement of segmental paving. Appearance does not verify the installed restraint.
Effective date
The date the appraisal opinion addresses, which can differ from the visit or report date.
The date to which the value opinion relates.
Efflorescence
A whitish mineral deposit that may form on masonry or concrete as moisture evaporates; not an identification of every white patch or its water source.
Salts left at a surface when salt-bearing moisture arrives and water evaporates.
Effluent
Liquid leaving a particular wastewater treatment stage; the term does not mean it is drinking water.
EIFS
Exterior insulation and finish system: identified insulation, reinforced base coat, finish and associated components working together.
Electric starter
Starting equipment that helps turn a fuelled engine; it is not the continuing energy source during clearing.
Electric thermal storage
A heating arrangement that stores thermal energy for delivery later; brick-core ETS uses a protected heated brick store.
Electrical notification
A record initiating the applicable authority process for stated electrical work; terminology and requirements depend on the jurisdiction.
Electrical service
The supply arrangement bringing electricity to the installation; its capacity is not established by counting panel spaces.
Electrode-steam family
The manufacturer-described family that passes electrical current through water to produce steam.
Embedment
The supporting material around a buried pipe. It is part of how a flexible pipe and the ground work together.
Emitter
The component or heated assembly that transfers supplied heat into a room, such as a radiator, baseboard or floor arrangement.
Enclosure interface
The junction where the deck or balcony meets the wall, doorway or other weather-protection layers.
Enclosure investigation
A scoped assessment of weather and moisture management with access and concealed-area limits.
Encroachment enquiry
A question about a feature and a boundary or affected interest, requiring the appropriate assessment.
Endorsement
A policy addition that can change, add, limit or restrict coverage; its actual wording and selection matter.
Energy
The amount used over a period, commonly expressed in kilowatt-hours for household electricity.
Energy balance
Accounting for energy entering and leaving a chosen boundary over a stated period, together with the change in energy stored inside it. A subtotal of heat gains is not a temperature or a temperature prediction.
Energy centre
Equipment managing thermal energy for a shared network.
Energy claim boundary
The component or home, period, method and result that the supported sentence describes. Keep the sentence within that scope.
Energy quantity
An accumulated amount in a stated energy unit, such as kWh or GJ; money, power and fuel volume have different units.
Energy recovery ventilator
Recovery ventilation equipment whose core transfers some moisture as well as heat between its air streams.
Entry point
A place where an animal may gain access to a building. A visible opening needs assessment before it is treated as a confirmed route.
Entry route
A path by which outdoor air and its contaminants can reach the interior.
Equipment finance
A payment arrangement connected to a purchase or other financing. Read the documents to understand ownership, security and ending conditions.
Equipment rental
An arrangement to use identified equipment under its terms. Regular payments do not automatically make it yours.
Equity arrangement
A separately evidenced model requiring its own legal explanation of capital, transfer and occupancy rights.
Erosion
Removal and movement of material through relevant natural processes.
Escape route
The household’s path to leave; portable equipment does not replace it.
Evaporation
Liquid water becoming water vapour, as at the named wetted pad.
Evaporator
The exchanger’s heat-absorbing role: refrigerant receives heat and boils into vapour.
The air-side heat exchanger where refrigerant absorbs heat in this heating explanation.
The cold-side heat exchanger where refrigerant absorbs heat from the room-air route.
Evaporator pad
A porous wet surface where passing air can gain water vapour.
Evapotranspiration
Water transpired by plants plus moisture evaporated from plants and soil surfaces.
EVEMS
Electric vehicle energy management system: specified monitoring and control that connects, disconnects or adjusts EV charging loads.
Event capture
A recording or measurement that preserves the relevant event and states its place, period and limits.
Event date and record date
When something happened or reportedly happened, and when the document was created. Record both if they differ.
Evidence brief
A concise record of the question, location, source information, access and requested deliverable.
Evidence index
A short list that points to the original records by document, date, location and scope.
Evidence status
The availability or review status of a record; it is separate from whether a component is sound, failed or assessed.
EVSE
Electric vehicle supply equipment: the assembly transferring power and exchanging relevant information between the supply circuit and vehicle.
Exclusion
An appropriate plan intended to prevent future wildlife access, with species, occupancy, timing and authorization addressed.
Exclusion work
Work intended to prevent animal access through identified locations while preserving the building’s other functions.
Exclusive use
A right reserved to a particular owner or unit over property that may remain shared; the governing documents matter.
Exercise run
A scheduled engine activity whose exact scope may exclude household transfer and load verification.
Exhaust air
Air carried from indoors toward its intended outdoor discharge.
Exhaust air leaving the power unit. The installed exhaust connections determine where that air goes.
Exhaust route
The intended route carrying combustion gases from the appliance outdoors.
Existing-condition assessment
An examination of a defined part of the property to inform the proposed work, with stated methods and limits.
Exit hole
An opening left by emergence; its presence alone does not establish current activity.
Expansion device
The component that lowers refrigerant pressure before the cooler mixture returns to absorb heat.
The heat-pump component that lowers refrigerant pressure and temperature before it absorbs heat again.
Exposure
The conditions reaching a particular site or building surface, influenced by orientation, terrain and shelter.
Exposure record
Dated notes about rain, cold, thaw or other conditions associated with a reported observation.
Exterior continuation
The actual space and route beyond an opening that must be considered with the opening itself.
External support
Conditions outside the pipe that an interior image alone cannot establish.
External-service dependency
A service outside the house, such as a communications network, whose availability is not established by local equipment having power.
Extinguishing agent
The material intended to interrupt combustion for the fire classes shown on the actual product label.
Extraordinary assumption
Uncertain information assumed for an appraisal that could materially change its conclusion if untrue.
Factory-certified scope
The portion and stated basis addressed by the actual certification program, distinct from site completion and subsequent alterations.
Fail-safe state
The specified safe operating behaviour when the relevant management conditions or information cannot support normal control.
Fan-coil
An emitter using a fan to move room air across a coil supplied with heating fluid.
Feasibility
A scoped assessment of whether a proposed adaptation can be carried out.
Feasibility scope
Coordinated questions needed to establish a workable intended use.
Field review
Professional review of implemented work and site conditions within its stated scope; distinct from the original design and a later current-condition assessment.
Fill valve
The part that supplies replacement water to an identified tank toilet; its design depends on the model.
Filler
A fitted interface piece that can allow the actual front to open beside a wall.
Filter medium
The material water passes through in a filter; its intended particle or treatment task must be identified.
Fin
A metal surface around an element or pipe that helps transfer heat to surrounding air.
Final grade
The documented finished grading stage before or with landscaping, as defined by the applicable local process.
Final permit status
The authority’s recorded state for a particular permit file; ask what that status means and which work it covers.
Finish coat
The exposed coating that gives the selected texture and colour over the prepared base.
Finish transition
The relationship between adjoining finished surfaces or interfaces, involving height, normal movement and product-specific details.
Fire class
A category describing the burning material or relevant energized-electrical condition.
Firebox
The chamber containing the fire; its construction and connections belong to the specific appliance.
First visible location
The place where water was first noticed. Water may have travelled there from a different source.
Fixed term
An arrangement with stated dates, whose current effect requires the actual terms and local advice.
Fixed-payment variable mortgage
A variable-rate arrangement whose payment may initially remain unchanged while the interest and principal portions change.
Fixture branch
A supply route toward a particular fixture or area, potentially beyond a circulating route.
The connection between distribution and an individual outlet; its actual extent needs identification.
Fixture drain
The pipe route carrying used water away from a sink or another fixture.
Flanking transmission
Transmission between rooms through connected paths other than directly through the nominal separating wall or floor.
Flashing
A water-protection detail at a roof joint, penetration or change of direction, such as a roof-to-wall connection.
Components and interfaces that maintain water control where a roof meets an opening, edge or another assembly.
A shaped water-directing component at a junction such as the top or bottom of an opening.
Flashing junction
A water-management connection where adjoining exterior parts meet, such as a roof and wall; actual layers require appropriate assessment.
Flight
A continuous sequence of steps between landings.
Float control
A liquid-level-responsive control that operates a pump switch according to the identified system’s design.
Float level gauge
An indicator linked to a float that follows the liquid level inside a container; it answers a storage-level question.
Floating finish
A finish not fixed to its supporting surface in the named method; connections between its boards still need identification.
Floating floor
A finish installed as its identified floating-floor system rather than mechanically fastened through a concealed heater.
Floor finish
The identified surface used and seen, kept distinct from product-specific intermediate layers and the supporting construction.
Floor moisture context
The distinction between room conditions, flooring material and substrate assessment, preserving the actual location, method and time.
Floor movement allowance
The product-specific way an assembly accommodates relevant expansion, contraction or other specified movement at its actual interfaces.
Floor plan
A drawing that looks down on a floor to locate rooms, walls, openings and other stated features.
Floor replacement extent
The physical rooms, layers, preparation and interfaces actually changed, alongside the construction that remained.
Floor sensor
A temperature-sensing component at an identified location in the floor assembly.
Floor warming
An intended comfort goal for the floor surface, distinct from an assessed whole-room heating requirement.
Flow
Water quantity passing during an interval, with units and measurement conditions.
Flow and pressure
Flow is an amount of water moving in a given time; pressure is the push at a stated location and condition. One weak tap is not a measurement of both.
Flow rate
Water volume delivered per unit time; distinct from pressure.
Flowing condition
A stated demand and operating context during a pressure reading.
Flue
The intended passage for combustion gases through the illustrated gas-heater design.
Flush closure
The seal or closing part intended to retain tank water between flushes, such as an identified flapper or canister seal.
Footing
The wider supporting base beneath the wall in the concrete-basement example.
A support element passing loads into its founding material. An ordinary visible floor slab does not identify its buried details.
Foreshore tenure
The actual authority or interest for occupying the identified foreshore.
Form
The component defining and supporting the concrete-placement space.
Foundation wall
The below-grade wall illustrated as supporting the edge of the house and separating the basement from soil.
Frame-to-wall interface
The junction connecting the window assembly to the surrounding building enclosure.
Frass
Insect-produced waste or boring material; a loose pile needs suitable identification before receiving that label.
Frost heave
Ground movement that can involve ice layers forming in frost-susceptible soil with available water and freezing conditions. A historical mechanism, not a property diagnosis.
Fuel-burning forced-air arrangement
An identified fuel-burning heat source delivering heat through household-air circulation, rather than assuming every furnace or heating system has the gas example’s routes.
Functional check
A check described by the actual device manufacturer. Its stated result concerns that device, rather than the whole home.
Functional verification
Assessment of whether an identified system or control performs its intended function under defined conditions.
Functional-check boundary
The identified device, method, date and warning functions included in the instructed check, with excluded detection and household-outcome questions retained.
Funding gap
A difference between required funds and confirmed available sources.
Funds deadline
The actual confirmed time by which the required recipient must have funds in the accepted form.
Furnace condensate
Water collected when a covered condensing gas design cools combustion water vapour during heat recovery, with model-specific handling separate from other nearby water.
Furring
Supporting strips in the identified wood example that separate the siding from the water-resistive barrier; actual arrangement and scope need matched documentation.
Gable
An end panel whose actual finish or support role must be identified.
Gallery
A passage or space excavated in material, such as wood used for a carpenter-ant nest.
Garage-to-home interface
The actual shared walls, floor/ceiling, door and junctions between garage space and adjoining home space.
Generation boundary
The place and quantity a production reading measures. Ask whether it represents generation, import, export, storage or another quantity.
Geotechnical
The study of ground materials and behaviour for a defined site and engineering question. Ask which locations, methods and proposed use were covered.
Geotechnical assessment
A defined professional investigation of relevant ground and site questions using its stated information and methods.
GFCI
A ground-fault circuit interrupter: an additional protective device that detects a loss of current and interrupts the supply.
Global stability
The broader ground-and-wall stability question, distinct from checking an individual wall component or visible face.
Grading approval
The applicable authority’s documented result for its inspected scope and conditions, distinct from preparing or submitting a certificate.
Grass-bag airflow
Air passing through the collection fabric while the intended bag retains clippings.
Gravity load path
The connected sequence carrying downward loads through the building’s parts and supports to the ground.
Gravity ventilation scheme
An air-movement arrangement relying on its designed non-mechanical driving conditions; not interchangeable with a mechanical-exhaust layout.
Gravity wall
A retaining arrangement whose resistance depends substantially on its weight and associated supporting arrangement; a visible block face does not establish this classification.
Grinding ring
The stationary chamber surface against which the named mechanism reduces material.
Ground-fault protection
In the GFCI discussed here, detection of current leakage followed by interruption of supply to reduce shock exposure; it does not create an equipment-bonding connection.
Guard
A protective barrier intended to help prevent falls, with its own structural connections and applicable requirements.
Handover
Actual completed-work, product, instruction and scoped verification records with outstanding items.
Usable operating and construction information transferred with the home.
The coordinated transfer of documents, permitted arrangements and access devices for the actual purchase.
Handover gap
A missing identity, record, finding or operating instruction for the system actually delivered.
Handover scope
The agreed equipment explanation, records, assessed condition, training and remaining tasks passed to the next owner.
Handrail and guard
A handrail supplies a gripping surface; a guard protects an open edge. Their functions may be combined in an identified assembly.
Hardness
A water property principally associated with dissolved calcium and magnesium; a specific treatment target, not a whole-water safety verdict.
Head
Pumping demand expressed as fluid height; actual elevation and route resistance matter to selection.
Header
Piping joining source-loop branches to the wider system route.
Header or lintel
A member above an opening carrying supported loads toward supports at the sides.
Headlease
The superior lease in a particular lease/sublease arrangement.
Heat conduction
Heat moving through food from a hotter region toward a cooler one, distinct from generating microwaves.
Heat delivery
The route by which stored warmth reaches the room; the named room-heater example uses a blower as a principal route.
Heat distribution
The connected route that delivers heat through the building, distinct from heat-producing equipment alone.
Heat exchanger
Surfaces that transfer heat between routes while keeping their fluids separate.
A device that lets heat pass between separated streams through its intended construction. It does not imply that their water mixes.
Heat exchanger or coil
A surface arrangement that transfers heat between refrigerant and air or another medium, which follow separate routes.
Heat pump
Equipment transferring heat under its designed process.
Heat recovery ventilator
Ventilation equipment that exchanges outdoor and indoor air while recovering heat between the intended streams.
Heat removal
Transfer of thermal energy out of the refrigerated space; the cooling task is distinct from a selected control level.
Heat request
A control demand interpreted using the actual device instructions, rather than a measured room-delivery result.
Heat source
The equipment or designed arrangement supplying heat to the distribution fluid, distinct from the floor or radiator releasing it into the room.
Heat storage
Energy retained by warming material and later released; no duration or measured capacity is assigned here.
Heat-transfer boundary
The intended exchanger relationship through which useful heat passes between the combustion side and household air; naming it does not establish actual integrity.
Heat-transfer plate
A metal component spreading heat from tubing toward the floor; the named underfloor example contacts the underside of the subfloor.
Heated area
The actual area assigned heating in the design, which may be smaller than the room footprint.
Heating-season coverage
The portion of the recorded test period occurring during the heating season.
High-efficiency detergent context
The actual model’s specified laundry-product type and use instructions; foam, product identity and known amount are observations rather than a complete leakage diagnosis.
High-level warning
An alarm indication of the high-liquid condition its identified equipment is designed and installed to detect.
Hinge jamb
The side of the door frame carrying the hinge connection in the identified hinged arrangement.
Hoistway
The enclosure within which the described elevator cabin travels; its actual construction and protection need matched evidence.
Hold point
A project-defined pause to check specified evidence and authorization before dependent work proceeds.
Home interest
The actual interest in the dwelling being acquired.
Hot-water return
The designated route carrying circulating water back within the actual hot-water arrangement; not the wastewater drain.
Household access task
The intended user’s complete route and activities, including approach, transfers/assistance and the destination—not only device travel.
Household escape plan
The actual household’s understood emergency response, practical route questions, assistance arrangements and outside meeting location.
Household function
An outcome such as safe shelter, drinking water or communication that can depend on several pieces of equipment and external services.
Housing charge
A continuing payment whose amount, inclusions and process require the actual co-op records.
Humidification
Adding moisture to air through an identified appliance process.
Humidifier care scope
The named components, tasks, assessed functions and exclusions recorded for a care visit.
Humidistat
A humidity control that uses sensed air and a selected target to request dehumidification.
A humidity control whose target requests a result; a sensor reading describes sampled air.
Humidistat target
The result requested by the humidity control, separate from a sensor reading.
Humidity target
The result a control is asked to seek. It is separate from a current reading and proof of an achieved result.
Hybrid tenancy
Alberta’s description of an arrangement starting fixed and continuing periodically under terms or later conduct.
Hydronic distribution
Transport of heat through a circulating-fluid arrangement to room emitters, distinct from forced-air duct distribution.
A water-based arrangement delivering useful heat within the building.
Hydrostatic pressure
Pressure from water that can be relevant behind a retaining arrangement; a stain alone does not measure or confirm it.
Ice dam
Ice that can obstruct meltwater drainage at a roof edge or another cold location.
An accumulation that can obstruct roof drainage after meltwater refreezes.
ICF
A permanent insulating form system used to create a concrete wall.
Identification
A finding about what an assessed material contains, tied to the tested location and method.
A supported finding about the insect or evidence, distinct from a skin symptom.
Identification finding
The provider’s stated conclusion about the animal or sign, with its evidence, location and uncertainty.
Identified extent
The specific locations and accessible components a material finding actually covers.
Ignition vulnerability
Features that may allow a fire or ember exposure to initiate burning; it is distinct from indoor smoke exposure.
IIC
Impact insulation class: a laboratory floor impact-insulation rating discussed in the historical NRC guide; it is not an airborne rating or a universal installed-floor promise.
Immersion element
An electric heating part extending into the water.
Impact assessment
An appropriate examination following a strike, whose scope may extend beyond sharpening.
Impact sound
Sound associated with mechanical contact that injects vibration into an assembly, such as a footstep on a floor.
Impeller
The rotating pump part that transfers energy to the fluid.
A rotating water-moving part inside a centrifugal pump.
The separate throwing part behind the central transfer area.
Impeller or lug
A blunt part on the named rotating plate that moves material against the fixed grinding ring.
Improvement
A unit feature whose treatment must be compared with the actual governing description and policy.
Included items
Things the purchase agreement says are part of the sale, which should be identified clearly rather than assumed from a showing.
Incoming water service
The pipe bringing water from a public main or private source into the building. A visible interior branch does not identify the entire service.
Incorporating record
A founding organizational document, distinct from admission of an applicant.
Independent heating and ventilation
Separate serving functions assessed under the applicable suite design; it is not synonymous with counting two furnace cabinets.
Independent support
A documented arrangement supported on its own structure rather than relying on a house ledger. Proximity to a wall does not identify it.
Individual conductor insulation
The covering on one conductor, distinct from a multi-conductor cable’s outside jacket. Appearance alone does not establish the installed role or metal.
Induction cooking
A category using a magnetic field with compatible cookware to create cooking heat; hot cookware can still heat the surface.
Infiltration
Water entering soil; the soil and ground cover affect how water is received.
Infrared sauna panel
A different product heating arrangement from a stone heater; applicable instructions and recall identity must be checked separately.
Injection injury
An injury in which a high-pressure stream enters tissue; urgent medical assessment is required.
Inlet valve
The intended one-way entrance to the illustrative pumping chamber.
Input uncertainty
How much confidence you can place in the observations entered, including the device, location, timing and measurement method.
Insert
An appliance fitted into an existing fireplace opening; the current appliance and connected arrangement need identification.
Inspection add-on
An explicitly agreed additional service with its own qualified scope, method and deliverable.
Inspection coverage
The route and surfaces the inspection actually reached, including its start, end and visibility limits.
Inspection limitation
An area, method or operating condition that was unavailable or outside the agreed assessment.
Inspection result
The recorded outcome for a stated inspection stage, date and scope, separate from a request to book a visit.
Inspection scope
The agreed purpose, areas, methods, deliverables and exclusions of a particular inspection.
The systems, methods and deliverables identified for a particular engagement, with applicable requirements and stated boundaries.
The exact unit, condition and questions covered by the reported inspection.
Inspection stage
A point in the construction sequence at which defined work can be assessed before later work changes or conceals it.
Installed airflow
Air volume moving over time at a named measurement location, under the recorded operating conditions.
Flow assessed in the actual connected configuration and recorded operating conditions, distinct from a product rating.
Installed limit
A documented maximum or constraint established for the accepted equipment configuration, distinct from its advertised capability.
Installed-system dossier
A record linking actual component identities, intended served areas, controls and scoped professional documents.
Insulating glass unit
A glazing assembly with panes separated by a perimeter-sealed space; its condition is distinct from the frame and installation.
Insulation resistance
A professional electrical assessment of unwanted leakage paths under its specified method.
Insurance deductible
The amount of a covered claim that the policyholder agrees to bear before the insurer pays the rest.
Integrated energy factor
Rated water removal per energy consumed, expressed by NRCan in litres per kilowatt-hour, or L/kWh.
Integrated pest management
An approach joining identification, prevention, suitable control and follow-up; often abbreviated IPM.
Integrated ventilation distribution
An arrangement using central forced-air ductwork for some ventilation delivery or collection.
Intended room use
The actual proposed household use, which should be stated rather than inferred from furniture or a listing label.
Intended use
The actual activities the buyer proposes, including people and equipment.
Intended user
A person identified within the professional report’s authorized use.
Interest rate differential
A lender-specific comparison of interest calculations used in some prepayment-charge methods.
Interface
A connection between the home and neighbouring land, shared access or services. Ask about both its physical condition and relevant responsibility.
A junction between components or systems where the relevant structural, water, air, heat or service function needs continuity.
A connection at an opening, penetration or transition between assemblies.
The junction where parts and control functions must connect.
Interface detail
The documented connection where components or control functions meet.
Interim occupancy
The named Ontario stage before registration/title transfer in applicable circumstances.
Interlock
A protective relationship between entrance status and device operation; seeing a door or lock does not establish function.
A documented relationship between controls, so their functions are not always independent.
Interlocking course relationship
The connection between neighbouring panel forms in the named vinyl example, distinct from attachment to supporting wall components.
Intermediate flooring layer
A named backing, underlay, bonding or membrane component with a specified role in an identified product system, rather than a universal extra layer.
Interpretation
The explanation drawn from evidence. Preserve any qualification and competing explanation.
Inverter
An electrical stage that produces alternating output from direct current; actual output and protections remain product-specific.
Investigation footprint
The actual locations covered by an investigation, distinct from a whole mapped planning area.
Investigation scope
The question, locations, methods and limitations included in a professional review.
The defined question, locations, operating conditions and methods covered by the provider’s work.
The question and evidence a provider is engaged to establish before a repair decision.
Irrigation programme
A set of watering instructions, separate from the physical group of pipes and heads.
Irrigation zone
A group of watering outlets served through a controlled branch of the irrigation system.
Islanding arrangement
The installed controls and connection arrangement that separate the backup supply from the grid during an outage.
Isolation scope
The identified area affected by a control operation performed by an authorized responsible provider.
Jacket legend
The actual printed identification on a cable’s outside covering, interpreted with its full wording and location rather than colour alone.
Joist
A repeated horizontal framing member supporting a floor or ceiling and carrying its loads to actual supports.
Kilowatt (kW)
A unit of power: the rate of energy use or transfer.
Kilowatt-hour
A unit of energy: one kilowatt used for one hour equals one kilowatt-hour.
Kilowatt-hour (kWh)
An amount of energy, distinct from a kilowatt (kW), which describes an energy rate.
A unit of accumulated energy; 1 kW sustained for 1 hour corresponds to 1 kWh.
Kitchen versus oven timer
In the named manual, a kitchen countdown does not control heat; the oven timer ends supported cooking modes, with documented exceptions.
Knob
A ceramic support holding a covered conductor away from a structural surface.
Lamina
The reinforced base-and-finish coating over insulation in the named EIFS example.
Lamp and fixture
A lamp can mean the light source or replaceable bulb. The fixture is the fitting that holds or contains the light source.
Landing
A level transition at an end of a flight or between flights, related to approach, direction and adjacent doors.
Landing entrance
The doorway or gate associated with a served level, separate from a travelling cabin gate where that arrangement is present.
Landslide
Movement of rock, soil or debris down a slope, with different possible materials and behaviours.
Latency
Communication delay; a different measurement from data-transfer rate.
Lateral load path
The connected assemblies and connections that transfer sideways forces toward resisting walls, foundations and ground.
Ledger
The house-side supporting board in the described attached arrangement; its backing and connection need assessment.
Legal access
The property-specific rights determined through actual documents and legal advice.
Legal description
The formal property identifier to reconcile across the agreement and records.
Legal interest
The actual documented ownership, lease, tenancy or other arrangement to be explained for the transaction by the appropriate adviser.
Legibility
A readable distinction between earlier work and an intervention.
Lender switch
Moving borrowing to another lender, subject to its approval and the transaction’s security requirements.
Lifting notice
The responsible authority’s message that an identified advisory has ended or changed, including any remaining actions.
Light kit
The lighting function integrated with or documented for a fan. Its control requirements need their own product information.
Light shaft
The lined passage connecting a roof-level daylight opening with the room ceiling below.
Limited common property
A British Columbia strata designation for common property reserved for specified strata lots; not a nationwide term to apply without records.
Line-voltage control
A control working with the heater’s electrical power, requiring matching equipment ratings and the actual installation.
Lint screen
A filter at its identified appliance location; its condition does not describe all internal or exhaust areas.
Load management
Control that changes when or how much selected electrical equipment draws, within an assessed installation.
Load path
The sequence of supporting components that transfers structural loads toward the foundation and ground.
The supporting relationships and connections by which actions reach other structure and the ground; a conceptual map does not establish capacity.
The connected supporting parts through which forces reach the house or ground; a picture supplies no capacity calculation.
The connected route through which building forces pass among members and supports.
The route by which building loads reach the supporting ground.
The structural route carrying loads to the supporting ground.
Load shedding
Control that temporarily prevents specified loads from operating under defined system conditions.
Loaded filter
A filter that has collected material during use; appearance alone does not quantify its resistance or remaining capture.
Local equipment
The equipment at the actual home or building boundary.
Local exhaust
Ventilation that captures air near a source, such as a suitable bathroom or cooking exhaust system.
A system that removes air near a source, such as a bathroom where bathing adds moisture.
Removal near an identified pollutant source through a suitable designed route.
Local function
A function performed by the installed device or local arrangement, distinguished from an internet service.
Locate scope
The components, methods and location questions covered by a professional assignment, with its recorded uncertainty and exclusions.
Log check
A crack associated with stresses in wood, including drying; the term does not establish structural significance.
Low-slope membrane
A continuous roof waterproofing system whose joints, interfaces and drainage need system-specific assessment.
Low-voltage control signal
A control instruction at a different electrical level from heater power; an appropriate relay arrangement may separate those jobs.
LPG
Liquefied petroleum gas; propane is commonly described this way because pressure allows storage as a liquid.
Magnetron
An internal component that produces microwave radiofrequency energy in the common design explained here.
Maintenance arrangement
The actual tasks, authority and costs assigned to responsible parties.
Maintenance history
The dated work, findings, parts and exclusions kept for the equipment, alongside separate performance and commissioning records.
Maintenance plan
The system-specific description of service, monitoring and follow-up appropriate to its components and use.
Manifold
An assembly that distributes supply fluid into branches and collects returns in the illustrated arrangement.
Manual applicability
Confirmation that the model, revision and component instructions actually match the equipment being discussed.
Mapped flood scenario
The stated process and conditions represented by a particular study product, rather than a complete parcel assessment.
Mapped scenario
The specified event or conditions represented by a hazard product.
Masonry veneer
An outer masonry layer in front of a separate wall. Its support, ties and drainage arrangement still need identification.
Mass appraisal
Valuation of groups of properties at a common date with property data and shared methods.
Mass masonry
A substantial masonry wall that can also support the building; identify its actual layers and any drainage spaces.
Master valve
A valve controlling the irrigation supply in an arrangement that includes one; it is not assumed present in every system.
Matched equipment record
A document whose address and equipment identity correspond to the actual installation being considered.
Matching instructions
Current guidance for the actual identified product and intended arrangement.
Material inventory
A record of material categories within the inventory owner’s stated scope; unknown entries and private portions need separate treatment.
Maximum output
A different manufacturer limit; it is not a continuing household capacity.
Measurement boundary
The system, space and conditions represented by a result.
The point or system whose energy or power a result actually describes.
Measurement channel
One named quantity or processed output of a device, with its own definition, method and units.
Measurement uncertainty
The limitations affecting a measurement and what differences it can meaningfully establish.
Mechanical coupling
Movement or vibration transferred between a pipe, supports and adjoining building materials.
Media resistance
Resistance encountered by air passing through the porous filter material under a stated condition.
Meltwater
Liquid water produced as frost or ice melts; its drainage and later freezing require their own context.
Membership
The household or person’s documented relationship to the organization, distinct from a unit title.
Membrane
An identified water-protective layer in the relevant assembly; a visible finish cannot establish its continuity.
MERV
Minimum efficiency reporting value: a tested particle-capture rating, distinct from installed airflow or pressure drop.
Metal lath
A metal reinforcement/support with openings that allow cement plaster to key around it.
Meter boundary
The service and connected loads represented by the record; shared systems or other fuels may fall outside it.
The electrical uses included in the utility meter’s billing record, which can include much more than one heater.
Meter-data interval
The period over which a meter export aggregates use; an hourly value does not reveal every shorter peak.
Metering orifice
An opening that meters water delivery in the named example.
Milestone
A defined stage tied to relevant work and evidence, not an owner technical test.
Mixed plumbing materials
Different materials in separate jobs or altered segments. Each segment needs its own location, identification and condition evidence.
MLS® HPI benchmark property
A modelled typical property for a supported area and category. It is not an inspected listing or a valuation of this address.
Model-matched handover
Instruction and evidence tied to the actual equipment, installation and responsibilities rather than a generic demonstration.
Model-matched manual
Manufacturer instructions verified as applicable to the actual product and relevant edition.
Model-matched service scope
The specific door, operator, components and instructed checks assessed by qualified service, with retained parts and exclusions recorded.
Module junction
A meeting of modules where structural, enclosure or service continuity may need distinct site-completed work.
Momentum
Motion carried by the mass of flowing water; a change in that motion requires force.
Monitoring
Dated evidence gathered under a stated follow-up method and interpreted in context.
Observation/reporting through the actual device and service, with its own dependencies.
Monitoring service
A contracted service for handling relevant system messages, separate from local sensing or public response.
Mortgage advance
Money actually released under the lender’s conditions, distinct from an early estimate or commitment.
Mortgage discharge
The process for releasing registered mortgage security after the relevant requirements are met.
Mortgage payout
A dated statement of the amounts required to settle the identified borrowing under the stated conditions.
Mortgage principal
The amount borrowed and still owing, distinct from interest charges and separately collected expenses.
Mortgage renewal
The next contract arrangement for debt remaining at the end of a term.
Mortgage term
The period covered by the present mortgage contract and its applicable conditions.
Motor
The part providing rotation to the fan assembly. Turning blades do not independently establish every other function.
Motor cooling
How air cools the motor. Thru-flow and bypass motor examples use different cooling arrangements.
Movement interface
A meeting point whose design must address relevant behaviour without an assumed universal detail.
Mulching route
A product-supported arrangement that retains clippings in the cutting process before returning them to the lawn.
Nailing hem and slot
The documented vinyl example’s upper attachment portion with elongated openings, associated with its movement provisions; no fastening method is supplied here.
Nesting material
Material used for a nest. Suspected rodent nesting material should not be disturbed for a closer owner investigation.
Nominal tank volume
The manufacturer’s labelled total tank-volume quantity; it is not a measurement of usable water currently available.
Non-equity context
A model in which market resale and capital rights must not be assumed from the word co-op.
Nonpotable
Water unsuitable for drinking; specific other uses still need their own appropriate requirements.
Normal operating control
A control intended for ordinary user operation; its presence does not make every proposed test appropriate or safe.
NOSI
A notice of security interest on land title. Ontario’s consumer-goods changes do not automatically cancel an equipment contract.
Nosing
The projecting front edge of a tread, where present.
Observation
What the author records seeing or otherwise assessing; retain the method, place and conditions.
Observation boundary
The component, visible surface, location and access that a record actually describes.
The actual locations, surfaces and conditions a record could show, including areas it did not reach.
Observed interval
The portion of an event actually witnessed, which may be shorter than its complete duration.
Occupancy agreement
The actual document addressing the offered dwelling and associated rights and obligations.
Occupancy finding
A bounded professional account of whether an identified location is being used, with method and limits.
Occupation feature
A physical feature such as a fence or driveway, distinct from a professionally established legal boundary.
Occurrence boundary
The contract's rule for grouping relevant events or losses for purposes such as applying a limit or deductible.
Off-gassing
Release of gases from a product or material; distinct from particles settling as dust.
Offer expiry
The stated point after which an offer is no longer open for acceptance under its actual terms.
Offset joint
A joint where the adjoining pipe ends do not line up. The observed extent and consequence require the provider’s explanation.
ONT
Optical network terminal; the provider-facing fibre interface in an identified arrangement.
Open system
A source-water arrangement with an incoming and receiving route needing actual assessment.
Open-cell structure
A material description in which many cells communicate; the conceptual picture does not identify a product.
Opener drive
The identified powered mechanism and connection that move a suitable functioning door, without replacing guidance or counterbalance.
Opening interface
Where the finish and backing relationships meet a retained window or door; visible trim alone does not establish concealed water-control continuity.
Opening-control device
Product-specific hardware intended to limit window opening under its designed conditions, with safety and emergency-use considerations.
Operating context
The configuration, use, weather and equipment state relevant to a particular observation or assessment.
Operating limit
A condition beyond which the existing plan or equipment cannot be assumed adequate.
Operating state
What the actual model is requested or allowed to do, such as dehumidify, circulate air, defrost or stop for its bucket condition.
Optical particle estimate
Particle information inferred from interaction with light and converted using stated assumptions.
Ordinary closure demonstration
A provider’s demonstration of identified door movement and latching at a stated visit, distinct from concealed-construction or weather-performance assessment.
Ordinary-use chronology
A dated sequence of natural observations and known changes used to frame the building question.
OSB skin
An oriented-strand-board facing that forms part of the pictured structural panel, distinct from its foam core and interior finish.
Outdoor evaporator
The outdoor heat exchanger acting as the heat-absorbing coil during heating in an air-source system.
Outdoor exhaust
A connected path carrying collected room air to an identified outdoor discharge.
Outer cable jacket
The outside covering around a cable assembly. Its colour alone does not authenticate conductor metal, a completed repair or suitability.
Outer jacket
The outer casing around the insulated tank assembly.
Outside meeting location
The agreed safe place outside where household members gather and are accounted for, with no re-entry for people, pets or belongings.
Oven mode
The identified requested heating and circulation function, separate from its selected target or a measured result.
Overburden
Landscaping, paving or other material above concealed components.
Overflow
The route for incoming water that cannot remain in storage.
Overpour
A separately specified poured layer containing tubing above a supporting deck in the illustrated floor arrangement.
Owner-builder authorization
A particular administrative status under the applicable regime.
Owner-controlled account handover
A change of service or device-account arrangements managed privately by the relevant owner and provider, without sharing passwords in the inspection file.
Panel profile
The cross-sectional form of the identified siding panel or board; it does not establish concealed attachment or backing condition.
Panelization
Prefabrication of assemblies such as wall or enclosure panels for site assembly; not automatically the same building class as a complete module.
Parameter
A particular substance, organism or property measured by a specified method.
Parcel boundary
The ownership boundary requiring actual legal/survey interpretation.
Parging
A coating over a foundation surface; a line in that coating does not show all of the backing material.
Parking bay
A physical space used to hold a vehicle; its markings do not establish the legal interest.
Passive cooling limit
A condition in which shading, natural airflow or other passive measures cannot meet the relevant need.
Payout statement
Dated amounts required to settle identified borrowing.
PDI
The applicable pre-delivery condition record and system orientation.
Perimeter drain
A foundation drainage component that collects groundwater near the base of the foundation; the actual route and discharge need property-specific confirmation.
Period average
The entered energy quantity divided by its valid day count, without an automatic correction for other conditions.
Periodic tenancy
An ongoing arrangement organized by tenancy periods under the actual agreement and local law.
Permafrost
Ground that remains frozen for at least two years. Its presence and local condition require evidence rather than a northern address alone.
Permission
A particular authority’s decision within its actual scope.
Personal contents
Belongings such as furniture and electronics, distinct from the building component enquiry.
Phase 1 environmental site assessment
A qualified history/records/site review aimed at identifying potential environmental concerns; separate from targeted sample findings.
Phase-cut dimming
A control method that changes the electrical power pattern delivered to compatible lighting. The term supplies no installation instructions.
Phased replacement
A programme with separately identified completed and remaining work, not automatic whole-building completion.
Phasing
Sequencing defined work while preserving an agreed temporary household arrangement.
Photo provenance
The date, location, provider, method and related report that give a supplied photograph its context.
Photoelectric protective input
An identified light-beam sensing function with the response defined in the matched opener instructions, rather than room-wide occupancy detection.
Photosynthesis
The leaf process using sunlight, water and carbon dioxide to make sugars supporting the tree.
Physical access
A route that can actually be travelled at the observed time.
Piston chamber
A pump space whose volume changes as the piston moves in the named teaching example.
Pitting corrosion
Localized corrosion attack discussed in copper guidance; identifying the mechanism at a property requires qualified evidence.
Plan identifier
The reference used in a registered or other governing plan, which may differ from the number painted at the bay.
Planned reminder
A calendar date to review a task, separate from evidence that the task was completed.
Plenum
A connected air chamber in the documented supply or return arrangement; its appearance does not establish all branch connections or measured delivery.
Podium
Outdoor area above enclosed parking or storage extending beyond the building footprint.
Podium assembly
An outdoor area over a supporting concrete slab and built space; paving, water protection and structure have separate jobs.
Point of entry / point of use
Treatment located at a supply entry or a particular use point; the actual connected branches still require confirmation.
Point-of-entry treatment
Treatment at the incoming home supply serving the connected downstream plumbing.
Point-of-use treatment
Treatment applied at the named use location; its findings do not automatically describe other taps or identify pipe material.
Treatment serving a particular use location, such as a dedicated drinking-water tap.
Policy endorsement
An issued policy provision modifying or adding coverage under its actual wording.
Pool filter
Equipment that removes particles from water as it passes through the filtering material.
Portability
A mortgage feature whose actual transfer conditions must be confirmed.
Post or column
An upright support carrying load downward through its actual base and lower supporting arrangement.
Post-flush refill
Replacement water supplied after an ordinary identified flush, distinguished from a later unexpected refill.
Post-mitigation verification
Measurement after installed work to assess its effect, with method, dates, location and purpose retained; initial verification and representative follow-up are separate evidence.
Post-tensioning
Prestressing carried out after the concrete has hardened, using stressed steel to apply forces to the concrete.
Power
The rate of energy use, commonly expressed in watts or kilowatts.
Power purchase agreement
An agreement to purchase generated electricity. Ask the legal advisor about the actual obligations and transfer provisions.
Pre-delivery inspection
In the applicable Ontario Tarion process, the builder-led visit before possession to explain the home and record its condition; the PDI form is not a warranty-service request.
Pre-existing-suite pathway
A specific authority process based on established history and conditions, rather than the house’s age alone.
Preapproval
A lender’s preliminary financing assessment; terminology and criteria vary, and it is not a guarantee of final mortgage approval.
Precautionary advisory
A protective notice issued while a potential risk or compromised operating condition is assessed; its instructions still apply.
Preheated water
Incoming water warmed before continuing through its documented supply route. The actual onward connection needs identification.
Prehung door system
A supplied door leaf already hinged within its frame; its installation into the opening remains a separate relationship.
Prepaid rent
A payment allocated to a future tenancy period under the actual records.
Preparation
Household tasks and access arrangements governed by the actual provider’s current instructions.
Prepayment privilege
A contract allowance for specified extra repayments without the otherwise applicable prepayment charge.
Presale agreement
A contract concerning a future property, governed by its actual terms.
Pressure
Force per unit area, recorded at an identified point under stated conditions.
A force-per-area condition; it is distinct from the quantity delivered during an interval.
Pressure and flow
Pressure describes a push at a location and condition; flow describes an amount of water passing over time. They need distinct measurement context.
Pressure difference
The pressure at one identified location compared with another reference location.
A difference between spaces that can drive air through a connected path; direction and size depend on conditions.
A difference in air pressure between places that can drive flow when a connected route exists.
Pressure drop
Pressure difference across a specified assessed component or boundary, reported with units and operating context.
Pressure regulator
A device that reduces a higher upstream pressure to a controlled downstream pressure; it does not measure stored fuel quantity.
Pressure switch
A control that responds to pressure conditions as part of starting and stopping a pump.
Pressure transient
A brief pressure response while an operating condition changes, distinct from a steady reading.
Pressure zone
A section of a building’s water supply served by a defined pressure-control arrangement; its actual extent and operating conditions need the building’s records and professional assessment.
Pressure-tank drawdown
Released water volume between the specified pump-cycle conditions in the described pressure-tank arrangement; not nominal tank volume or guaranteed outage water.
Primary storage
The vessel or boundary intended to retain fuel during normal storage.
Product application
The defined use and conditions belonging to an identified item. A generic colour or material label does not establish an installed match.
Product approval scope
The product or component and conditions addressed by its approval or evaluation, distinct from the complete installation.
Product evaluation
An assessment of a named product under stated conditions and code scope.
A scoped assessment of a named product and its conditions, not certification of an existing house.
Product line
The documented onward fuel route from storage toward the oil-burning equipment, separate from filling and venting.
Product water
The treated-water stream produced by a membrane treatment process.
Product’s intended use
The applications and limits described for the exact pipe or fitting, considered with locally applicable requirements.
Professional handoff
A transfer of a defined question and relevant evidence to a person qualified and engaged to answer it.
Project funding boundary
Which defined costs and phases a funding decision covers, and which remain excluded or unresolved.
Project phase
A separately described portion of a project. Its label does not establish approval, funding or completion.
Propane
A fuel that can be stored as a pressurised liquid and used in its gas form by appropriate appliances.
Property status
Actual occupancy and use circumstances described to the relevant insurer/adviser.
Property-specific insurance response
The insurer or authorized broker’s current response to the actual disclosed application facts, with any conditions kept separate from policy coverage.
Property-specific scope
A description of the location, question, access, work and exclusions that a particular service or proposal covers.
Proposed resolution
A decision presented for consideration; its presentation does not establish that it was adopted.
Proposed-use overlay
A clearly labelled communication drawing showing desired work beside known and unverified location information. It supplies no sewage design or project permission.
Prorated charge
A charge calculated for part of a period rather than the full usual period; the actual account’s method and dates matter.
Protected route
The confirmed drain branch or connection on which a particular backwater device acts.
Protected-load schedule
The installed backup record identifying the supplied loads and exclusions; separate from a generic whole-home claim.
Protective finish
A separate covering or treatment serving its specified protective role; the insulation itself does not establish that role.
Protective function
The electrical condition a device is designed to detect and respond to. One device can have several functions.
A model-specific response to a defined abnormal condition, distinct from ordinary comfort control.
Provenance
Who supplied a record, when, which place or component it concerns and the context needed to interpret it.
Where the item came from and its purchase or replacement history.
PSIG
Pounds per square inch measured relative to atmospheric pressure; a pressure unit, not water volume or delivery rate.
Pump cycle
A connected sequence of collection, level rise, pumping, level fall and control stopping.
Racking
Sideways distortion of a frame. Connected bracing or sheathing can resist it as part of the actual design.
Radiant cooking surface
A category using an electrically heated source to transfer cooking heat through the surface to cookware.
Radiant heat
Energy transferred toward surrounding surfaces and people from a warmer surface.
Radiation
Heat transfer from hot surfaces toward surrounding objects.
Radiofrequency energy
The form of electromagnetic cooking energy described by Health Canada; distinct from retained food heat.
Radon rough-in
A construction provision for later radon-system work, whose actual completed scope must be identified; its presence alone is not a measured reduction in occupied-space radon.
Rain-management strategy
The assembly’s intended way of handling rain exposure and water that passes the exterior.
Rainscreen
An arrangement with cladding separated from backing so the intended space and connections can assist rain management, drainage and drying.
Rated energy
Energy information for a model or home under its stated rating conditions. It differs from a household’s actual use.
Rated output
The manufacturer-stated continuing capacity under its specified conditions.
Raw water
Water before the treatment stage being evaluated.
Reached endpoint
The documented end of the actual camera assessment, not every downstream component.
Read status
The utility’s description of a meter reading, such as actual or estimated.
Real Property Report
An Alberta land surveyor’s site report used in the described Calgary process; its date and scope matter.
Receiver
The pressure-containing tank that stores compressed air between pumping and outlet demand.
Receiving drain handoff
The point where the washer’s discharge is received by its identified building-plumbing arrangement; proximity to an opening does not establish an approved connected route.
Receiving route
Where collected or redirected water goes next, with site and local constraints.
Where water and removed material go after leaving the cleaning target.
The actual destination and continuation of drainage, requiring appropriate technical and local context.
Receiving system
The actual building drain and sewage destination with its own conditions and local requirements.
Rechargeable extinguisher
A unit designed for appropriate fire-equipment servicing after use or another relevant condition.
Reciprocating pump
A pump in which a piston repeatedly moves within a cylinder to compress air.
Recirculating hood
An arrangement returning air to the room through its particular treatment components rather than discharging that flow outdoors.
Recirculation
Movement of indoor air through a route that returns it to indoor space.
A supported mode moving indoor air without the same exchange with outdoors as ventilation mode.
Movement of water through the system’s equipment and back to the pool or hot tub.
Movement of air within the space, without by itself establishing outdoor-air exchange.
Water movement around an identified supply-and-return route, rather than every movement ending at an open fixture.
Record chain
Linked project, installation, inspection, change and follow-up records that describe a named component through time.
Record discrepancy
A specific mismatch in location, identity, use, scope, date or status requiring clarification.
Record mismatch
A specific inconsistency in scope, identity, status or dates that needs clarification.
Recording retention
The actual settings and arrangements governing how long recordings are held; copies can have separate paths.
Recovery
Restoring heat to stored water after use.
In the named manufacturer examples, anticipatory operation intended to approach a future scheduled target; the actual feature and display are model-specific.
Recovery core
The internal assembly where heat, and for an ERV some moisture, transfers between neighbouring air passages.
Recovery record
Water-level observations after the test pumping stops, interpreted with the actual test method and conditions.
Recovery scope
The identified checks and qualified actions needed before an affected system returns to ordinary use.
Rectifier
An electrical conversion stage that changes alternating current into direct current in the named inverter architecture.
Recurrence
A condition appearing again after an earlier action. The repeated pattern does not identify the cause by itself.
A symptom observed again on a recorded date and under recorded conditions.
Reference period
The time described by the observations. It can be earlier than the publication date.
Referral relationship
The selection, compensation or other connection behind a professional introduction, to be evaluated under applicable obligations.
Refinancing
A changed borrowing arrangement that can alter debt, repayment or funds available.
Refrigerant
The working fluid that absorbs, carries and releases heat while circulating inside the heat-pump system.
The working fluid in the heat-pump circuit that carries transferred heat.
The working fluid that absorbs, transports and releases heat in the source's functional cooling explanation; it is distinct from defrost water.
The working fluid carrying heat through the heat-pump cycle.
Refrigerated dehumidification
Removing some airborne water vapour by moving air across cooled surfaces, where droplets form and follow a separate liquid route.
Regenerant / brine
The concentrated regeneration solution used by the documented process to restore exchange capacity; this definition supplies no chemical selection or handling instruction.
Regeneration
The documented restorative sequence that releases retained material, replenishes exchange capacity and returns the appliance to service.
Register boot
The duct fitting connecting a branch duct to its room outlet opening.
Registered instrument
The underlying document associated with a registered entry; its effect needs legal interpretation.
Registered interest
An interest recorded on a land title; its meaning for a purchase or intended use needs the relevant document and legal advice.
Registration confirmation
A named authority’s record confirming a registration relationship; scope depends on the programme and actual tank identity.
Regulator
A control for outlet-side pressure, distinct from the receiver’s automatic pumping limits.
Regulator stage
One pressure-reduction step in an identified supply arrangement. The number and form of stages depend on the actual system.
Reinforced-soil system
An arrangement in which reinforcing elements within the soil and the wall face form parts of the retaining system; the concealed extent must be established.
Reinforcing mesh
In the named EIFS example, glass-fibre fabric embedded within the base coat; different from the metal lath in the cement-stucco illustration.
Reinforcing steel
Steel incorporated in concrete to participate in the designed structural response.
Reinspection scope
The particular areas, work or questions examined in a later assessment, with its date, methods and remaining limits.
Reinstatement
Rebuilding the components and finishes for the intended use.
Repairing finishes and affected areas after access for the work.
Reject stream
Water carrying material left behind by the membrane process toward the specified discharge arrangement.
Related-file ledger
A short index of connected files, their types, document versions and individual statuses. Keep each file’s status separate.
Relative instrument indication
A reading used as a comparison within an identified method and material, not automatically a universal percentage of water content.
Relay
A component that can let a control signal govern another electrical load; its suitability and arrangement are model-specific.
Remaining term
The period left under the actual lease.
Remaining-capacity record
A quantity reported within the named control scheme, distinct from a current measured output-water result.
Remediation
Defined treatment or removal of affected material within an actual scope.
Renewal
A future continuation governed by its actual process and terms.
Renewal boundary
The record of parts and junctions that work removed, retained and reconnected.
Repair extent
The specifically identified stretch or components addressed by a completed job, with start/end limits.
Repair scope
The named location, component and tasks covered by the work; other wet materials may need a separate assessment.
The actual locations, layers, findings and work included in a repair—not simply its finished appearance.
The defined components, locations and work included in a selected repair package.
Replacement air
Air that reaches the room or home as exhausted air is removed. Its route affects performance and pressure.
Air entering to replace air exhausted from the building or suite; its route and suitability need assessment.
Replacement boundary
The documented start/end points, branches and exclusions of completed replacement work.
Replacement extent
The equipment, connected work and interfaces actually changed, recorded alongside ducts, appliances, controls or vent components that remained.
The location-specific components and interfaces actually changed, recorded beside removed, retained, opened and restored work without assuming whole-wall renewal.
Replenishment
Water entering the well or documented storage from its source over time; separate from the rate the installed pump can deliver.
Report addendum
A later document clarifying or adding to a report. Keep it connected to the original version and scope.
Reported resolution
A statement that an earlier incident was addressed. Keep its supporting report and any unknown cause clear.
Representative average
A result supported by a measurement period and placement suited to the intended exposure decision.
Requested temperature
The thermostat’s target, distinct from measured temperature throughout a room.
Reserve assumption
A scope, cost, timing or service-life premise used in a financial plan.
Residual cooking heat
Heat remaining in cooking surfaces, cookware or cavity materials after a requested heating function ends.
Residual mapped risk
Risk that remains within the study's stated assumptions even where a protective feature or mapped boundary is present.
Residual risk
Exposure remaining after a chosen measure.
Resilient mounting
A mounting arrangement with controlled flexibility between a surface and its support; its performance depends on the complete identified assembly.
Resin
The exchange medium described in the softener example; retained hardness reduces its remaining softening capacity.
Resistance element
The heater part that converts electrical energy into heat.
An electrically supplied component that produces heat for the storage core.
Resistance heater
A manufactured element that converts electrical energy into heat; its form and permitted installation are product-specific.
Resolution
The displayed or reported increment, which does not by itself establish accuracy.
Response path
The contacts, access and decisions that connect a concern to appropriate action.
Response policy
The applicable service or authority’s conditions for acting on a message, distinct from notification delivery.
Response record
Dated ordinary room observations linked to control state and context, with unresolved causes kept explicit.
Responsibility map
A component-by-component record of authorization, access, maintenance and cost responsibilities, tied to governing documents.
Restraint
Something limiting free material movement, which can create stress when dimensions change.
Retained extent
The identified old wiring remaining, with its assessment limits.
Retained ground
The soil or other ground material whose level the wall arrangement supports; its actual composition and condition require appropriate evidence.
Retained wiring
Old wiring left in place after a defined project; its extent and status need an accurate account.
Return air
Household air travelling toward the identified circulation equipment through the actual return arrangement, distinct from combustion air.
Return path
The available route by which household air travels from an occupied room back toward a circulating blower.
Return to use
A decision about the identified space and intended household use under the actual advice and conditions.
Return-to-use directions
The actual incident and equipment instructions for resuming household water uses after restrictions change.
Return-to-use instructions
The actual provider/manufacturer directions governing use after specified work, with scope and limits.
Reveal
The visible gap or relationship between adjacent window components, interpreted for the specific product.
Reverse osmosis
Pressure-driven movement of water through a selective membrane, producing treated and reject streams.
Reverse-cycle defrost
A frost-removal sequence that changes the refrigerant cycle to deliver heat to the outdoor coil.
Reversibility
Ability to undo a particular intervention, assessed in its context.
Rise
The vertical change between successive finished step levels; the adjoining finished floors belong to the end-transition question.
Riser
A pipe route serving different building levels; actual service and responsibility need identification.
Roadside ditch
A drainage feature serving the road; its legal type needs identification.
Rodent sign
An observation such as a sound, mark or damaged package that raises a rodent question. Its meaning needs identification and context.
Roof assembly
The connected parts that support the roof and manage weather, heat, air and moisture. Their arrangement depends on the actual roof.
Roof covering
The outer roofing product, considered separately from the complete supporting and water-control assembly.
Roof deck or sheathing
The supporting surface beneath the roofing. This use of “deck” is different from an outdoor walking area.
Room demand
A request for warmth from the occupied space through the relevant room control.
Room heat loss
The heat leaving a room through its enclosure and air exchange under stated conditions.
Room response
The observed temperature or comfort change under stated operating conditions.
Roost
A place used by bats for resting or other life-stage needs; its actual status requires suitable assessment.
Root zone
The actual soil and roots supporting the tree’s living and physical functions, not a universal circle copied from a canopy.
Rotary mower
A mower using a powered rotating cutting system within a deck.
Rough grade
A shaped base at the documented construction stage, with its meaning and approval process defined locally.
Rough opening
The building opening receiving the door system, with construction and interfaces distinct from the moving leaf.
Rough-in
An installed portion of a system before finishes or final fittings conceal or complete it; its particular stage record does not show every later change.
Route extent
The connection, duct and termination portions actually covered by observation, records, cleaning or assessment.
Router
Equipment directing communication between the home network and another network.
Run
The horizontal progression between successive riser positions, distinct from the full surface of a projecting tread.
Run time
How long watering is requested for a station; it does not measure delivered water volume.
Runtime estimate
An estimate of supported duration under stated load, battery and operating conditions.
SACC
Seasonally adjusted cooling capacity: a portable-unit rating under its defined method and configuration.
Sacrificial anode
A component consumed while helping protect a tank design that uses it against corrosion.
Safety valve
A protective pressure-relief device, not the normal outlet regulator or an owner adjustment.
Sale proceeds
Money remaining after the actual settlements and included selling amounts.
Sale status
The property-specific authority and conditions affecting the proposed transaction.
Sales mix
Which properties contributed to the sales group. A changed mix can move its average even when invented category prices remain unchanged.
Saltwater chlorine generator
A device using electrical energy to generate chlorine from salt in the water.
Sampling point
The identified location where water was collected, including whether treatment was upstream.
Sampling purpose
The defined question a sampling design aims to answer, such as exposure assessment, contribution investigation or corrosion-control evaluation.
Sash
The window component holding glazing; in an operable unit it moves relative to the frame.
The window component holding glazing; an operable sash moves relative to the frame.
Sauna drying function
The intended post-use moisture-removal arrangement, which needs an actual system explanation.
Sauna heating element
The electrical heat-producing component in the identified heater.
Sauna high-limit protection
A separate protective temperature function, distinct from the user’s normal comfort request.
Sauna stone compartment
The designed region that supports the heater’s specified stones and intended heat/air relationship.
Sauna thermostat
The temperature-related control function in the identified sensing arrangement.
Scaling
A concrete flaking or peeling surface process, whose identification and relevant exposure or construction history require assessment.
Flaking or loss from a hardened concrete surface. Naming the observation does not choose its cause or severity.
SCFM
Standard cubic feet per minute, a delivery quantity whose reference and pressure conditions matter.
Schedule override
A documented hold or other active instruction that changes which scheduled target governs the control.
Scope
The question, methods, access and limits included in an assessment.
Scope assumption
A condition a proposal relies on but has not necessarily established through evidence.
Scope boundary
Which equipment, circuit and questions an assessment actually covered, including what was left unexamined.
The part of a question or property outside the booked professional assessment.
Scope exclusion
A component or question that a professional assignment did not evaluate.
An area, system or question a provider did not assess or cover.
Scope limitation
A part, surface or question the stated inspection could not address. Keep that limit beside the findings.
Scope matrix
A question-by-question table matching the component, provider, method, access and written deliverable.
Scope of work
The particular rooms, tasks, materials and exclusions a project or document describes.
The agreed assessment, research and analysis, with the applicable methods and limits.
Scoped closeout
A completion entry that identifies the question, work or check, conditions, result and remaining limitations rather than declaring every related issue resolved.
Scoped measurement
A result kept with its method, location, time and operating conditions instead of treated as universal clearance.
Scoped recheck
A later examination of a specifically defined item or completed work, retaining its own access and method limits.
Scraper
The long lower collection edge between the front housing sides, separate from the auger.
Scratch coat
The first base coat in the illustrated three-coat cement-stucco example, surrounding the lath and scored for the next coat.
Seasonal assessment limit
A specific part of the assessment that cannot be completed in the system’s present opened or closed state.
Seasonal metric
A performance measure combining specified conditions under a named seasonal method; it is not a future household bill.
Seasonal storage
A longer period out of use, governed by that product’s instructions.
Seasonally adjusted annual rate
An adjusted pace expressed on an annual basis, rather than the raw number occurring during one month.
Secondary containment
An additional identified arrangement intended to retain a release from primary storage; its capacity and condition need actual evidence.
Secondary loop
A separate fluid circuit exchanging heat with the heat pump’s refrigerant circuit.
Secondary suite
A self-contained living arrangement within a house; the applicable local and legal definitions must be confirmed for the actual use.
Section drawing
A view through a marked cut in a building, used to explain relationships that a view from above can hide.
Sectional overhead door
A moving barrier made of joined sections that change relative angle while following the identified route between the opening and overhead position.
Security deposit
Tenant money with a separate purpose and legal treatment from rent and the purchase deposit.
Seismic hazard
Modelled information about potential earthquake ground motion. A separate building assessment addresses the actual structure and its response.
Selected level
A documented warmer-to-colder choice in the named example, distinct from a measured compartment temperature.
Self-propulsion
Powered assistance for movement across the ground, which is a different function from cutting.
Sensible heat
Heat associated with changing temperature, considered separately from energy transfer involving moisture.
Sensing location
The element or area where a device detects its specified condition; it may differ from the location of the device body.
Sensor location
The place whose measurement contributes to the control temperature; it may differ from the wall display or an occupied room.
Series loop
A route in which fluid passes through successive emitters before returning; the actual installed arrangement must be established.
Served air path
The actual room or duct route through which air reaches and leaves the appliance; a category name cannot verify every room served.
Served-area record
The evidence identifying which spaces an installation is intended to serve; separate from a whole-home marketing description.
Service
The documented operating function in which incoming water undergoes softening.
Service agreement
An agreement for defined support or work. It may be separate from who owns the appliance.
Service boundary
Where the applicable responsibility or service scope changes.
Service chase
A planned route for services, not permission to cut an arbitrary new route through a structural panel.
Service isolation
The actual product’s arrangements for preventing hazardous energization or movement during defined work, not merely a silent engine.
Service portion
A specifically described part of the incoming water-service route, using the local provider’s endpoints and responsibility terminology.
Service reinstatement
Restoring an affected connection to its intended service after work, with method-specific confirmation.
Service scope
The equipment, tasks, observations and checks included in an agreed visit.
Serviceability
Performance in use, including bending and vibration, considered separately from ultimate load-carrying strength.
Setpoint
The temperature target used by a control, distinct from a reported temperature or the achieved condition in another room.
Settlement
The actual insurance financial arrangement, distinct from performed work.
Sewage ejector
A pumping arrangement that lifts collected wastewater from connected low fixtures toward its identified receiving drain.
Sewer lateral
The connecting pipe between the building drainage and municipal sewer. Local rules determine who owns and maintains each part.
Shaft air barrier
The connected air-control boundary limiting room air movement into surrounding construction.
Shared service
Infrastructure or service used by more than one property under its own arrangement.
Shared system
A system or assembly extending beyond one dwelling; its actual route and responsibility require property-specific evidence.
Shared user
A user with the permissions defined by the actual account arrangement, not automatically owner authority.
Sheathing
An enclosing layer associated with the tendon system; its material, condition and protective role depend on the actual system.
Shell package
A supplier’s stated structural-shell scope, distinct from completion of the entire house.
Shelter
A protected place an animal may use to hide or nest, separate from its food source.
Shore work
A particular activity whose permission needs jurisdiction-specific review.
Shoreline
The physical water-and-land interface, which can change.
Shower pan liner
A water-control layer below the mortar setting bed in the traditional shower arrangement described here; its drain relationship differs from a bonded system.
Sill pan
A beneath-opening water-management component in the named manufacturer example, intended to collect incidental water and direct it outward; presence cannot be inferred from visible trim.
Simultaneous flow
Two relevant streams moving during overlapping time. It describes a recovery opportunity, not a recommended longer draw.
Sink flange
A named sink-interface part, distinct from the complete mounting and seal assessment.
Site completion
Property-specific support, assembly, enclosure, service and finishing work required beyond the delivered factory portion.
Site interest
The actual right to occupy or use the identified land.
Skid shoe
A short support at the side of the front housing, with a wearing surface that meets the ground.
Skylight curb
The raised supporting construction around a roof opening on which a curb-mounted unit sits.
Skylight flashing
The connected weather-protection details directing roof water past the skylight opening.
Skylight glazing
The transparent part of the roof opening, with a product-specific construction and performance.
Slab
The concrete floor surface in the basement example; a different part from the foundation wall.
Slab on ground
A slab supported by underlying ground, distinct from a suspended structural floor above another space.
Slip joint
A drain connection in which a tube enters a receiving fitting, with a washer and retaining nut in the illustrated type.
Slope stability
The separate question of ground movement or failure.
Smoke detection function
The identified device’s sensing role when smoke reaches its relevant location; not a measurement of every room or hidden space.
Smoke-tight separation
A designed continuous boundary intended to limit smoke passage; visible finishes alone do not verify all concealed details.
Snow load
The action of accumulated snow on a structure; depth alone does not establish it.
Snowblower auger
The spiral gathering component that feeds snow toward the next part of the designed material route.
Snowblower impeller
A separate throwing component behind the auger in the conceptual two-stage arrangement.
Snowblower scraper
The lower collection-edge component in the named examples; condition and setting are model-specific.
Snowblower skid
A support component relating the front housing to the ground on the identified design.
Solar equipment schedule
A list of the home’s panels, inverters, storage, controls and monitoring equipment, with available model numbers and dates.
Solar heat gain
The contribution of solar energy entering or being absorbed by the building and affecting its heat balance.
Solar heat gain coefficient
The fraction of solar heat transmitted by the identified product under its rating basis.
Solar-ready provision
Documented preparation for a future solar project. Ask what was supplied and what work remains before accepted generation can operate.
Solenoid valve
An electrically controlled water valve.
Source
An activity, material or location releasing the substance under investigation.
Source capture
Collecting cooking-source air near where it is generated before it spreads widely through the room.
Source control
Avoiding or reducing a pollutant source rather than assuming another device will remove everything it emits.
Addressing the actual material or activity producing the concern, rather than relying only on air cleaning.
Work directed at the cause of damage.
Measures directed at the actual contaminant-generating activity.
Source exchanger
The ground or water arrangement transferring heat under the actual design.
Spalling
Breaking or flaking of material from a surface; the word describes damage, not one confirmed cause.
Concrete flaking or breaking away; actual significance needs professional assessment.
Loss or breaking away of concrete surface material; its cause and significance need assessment.
Special assessment evidence chain
The connected records explaining one assessment’s purpose, decision, funding and unit information; not a substitute for legal interpretation.
Specialist referral
A recommendation for a qualified person to assess a defined question beyond the reported work.
Specification baseline
The actual documented promised layout, finishes and selected items.
Spillage
Smoke or other combustion gases entering the room instead of being carried outdoors through the intended venting route.
Splash containment
The enclosure and opening question concerning water remaining within the intended wet area during ordinary use, separate from hidden assembly condition.
Splice
A connection joining conductor sections; the installed combination and surrounding arrangement need appropriate assessment.
Spline
A joining component used in some panel connections; its type and role depend on the system and design.
Spray polyurethane foam
A foam material formed where applied from its specified components; the actual product and installation matter.
Sprinkler deflector
A component shaping supplied water into the identified model’s intended distribution pattern; a picture establishes no installed coverage.
Sprinkler orifice
The waterway opening in an identified head through which supplied water passes after its documented opening mechanism operates.
Sprinkler thermal element
The heat-sensitive operating component in an identified automatic head; its local response belongs to that head’s documented mechanism.
Sprinkler valve supervision
An identified control-status monitoring role; the Vancouver example concerns trouble indication in specified buildings other than houses.
Sprinkler verification scope
The particular installed-system question, configuration, conditions, date and exclusions addressed by a documented assessment.
Stack effect
Pressure relationships associated with temperature-driven differences in air density within and around a building.
A temperature-related building pressure pattern associated with different air densities and connected leakage paths.
Stacked-log wall
A wall formed by substantial horizontal logs, with actual support and enclosure roles requiring identification.
Standard-unit definition
In Ontario condominium guidance, the defined unit elements used in repair-after-damage questions, requiring the actual governing documents rather than an assumption based on finishes.
Standard-unit description
The relevant governing description used to reconcile unit components and insurance/repair questions in its jurisdiction.
Standing time
The applicable food instruction for heat distribution/completion after cooking energy ends.
Start time
When a watering programme is requested to begin; its meaning should be matched to the actual controller manual.
Start/stop controls
The start/stop controls that tell the unit to run. They have a different job from the pipes carrying air and dirt.
Starter
The supported event or instruction beginning a rule’s evaluation.
Starting battery
The battery serving engine starting and associated generator functions, distinct from household energy storage.
Starting demand
The electrical demand associated with an appliance beginning operation, which may differ from its continuing demand.
Static condition
An identified no-flow condition at the pressure measurement point.
Station
A controller output associated with a valve in the identified model; a numbered label does not establish the actual yard area.
Statutory protection
A legal obligation under the actual applicable regime, distinct from insurance.
STC
Sound transmission class: a single-number airborne rating associated with element transmission data, distinct from overall installed room-pair performance.
Storage heater
A heater that keeps a reserve of heated water in a tank.
Stored heat
Energy held in materials that can affect temperatures after the original gain changes.
Stored pressure
Energy held in the assembled vessel that supports discharge through the intended valve and outlet.
Strain relief
The supported flexible section where a cable enters a plug or enclosure.
Strainer
A small screen in the named incoming-water route.
Strike jamb
The opposite frame side where the identified leaf’s latch meets its receiver.
Stringer
A member supporting steps along a flight; a visible finish does not reveal every connection or its capacity.
Structural insulated panel
A composite building panel with structural facings bonded to a rigid insulation core; actual systems and uses differ.
Structural rib
A member included at specified locations in a panel system to participate in the designed structural arrangement.
Structure
The component supporting the loads assigned by the actual design.
Structure-borne sound
Vibration travelling through solid building elements and connections; it may later radiate as airborne sound.
Subfloor
The structural floor layer beneath the finished flooring; it carries loads between joists and participates in the specified floor assembly.
Subject property
The actual home being considered.
Sublease
A subordinate lease whose own terms and dependencies need review.
Substrate
The material receiving a coating or repair; ask whether the actual condition meets that product’s requirements.
The surface receiving the applied material, such as the relevant wood or other construction surface.
Substrate suitability
The identified receiving material and condition assessed against the applicable product-system requirements, distinct from whole-floor structural capacity.
Suction outlet
An opening where water is drawn from the basin into a connected route; its protective arrangement requires qualified assessment.
Sufficient outlet
The safe/legal drainage outlet described by the named Ontario guidance.
Suitability
A household-specific decision informed by competent advice, not a universal label.
Suite registry record
An actual address-linked authority record with its stated scope and status; later changes need separate consideration.
Supplementary assessment
An additional assessment within the relevant authority’s process; actual scope needs confirmation.
Supplementary heat
An identified additional heat source supporting the system under its documented operating arrangement.
Supplementary heating sequence
The installation-specific intended coordination of the heat pump and another heat source, as documented by the responsible provider.
Supply air
Air delivered toward an occupied space; its outdoor-air content depends on the identified route and arrangement.
Household air delivered from the identified equipment through its actual supply arrangement to served spaces.
Supply branch
A duct route carrying conditioned air from a shared supply trunk toward a room.
Supply connection
The incoming-water connection feeding a fixture or appliance.
Supply handover
The practical transfer of equipment information, responsibilities, contacts and confirmed service arrangements when a home changes hands.
Supply-path identity
The documented source, treatment and plumbing route serving the relevant outlet.
Supporting floor
The actual assembly carrying and distributing floor loads; its construction and assessment are different from the finish selected above it.
Surcharge
A raised sewer water level that can push water backward along connected drains.
A raised level or pressure in the sewer that can push wastewater back towards connected homes.
Additional loading considered in the assessment, such as nearby vehicles, structures or stored materials; no safe distance or allowed load follows from the term alone.
Surface margin
The entered surface temperature minus the calculated dew point. It helps compare a particular surface with conditions that can support condensation.
Surface runoff
Water travelling across the ground or other surfaces toward a receiving route.
Surge
A brief voltage rise; a different condition from loss of normal supply.
Surge-only outlet
An output with stated surge protection but no battery-backed continuity.
Surround
The construction or finish around the fireplace, including its relationship to the model’s instructions.
Suspended-tube method
The separately specified below-subfloor arrangement holding tubing on clips with an intentional airspace, rather than plate contact.
Swale
A broad shallow depression used to carry surface water along a planned route.
A shaped surface-water route; its approved configuration and maintenance responsibilities need local confirmation.
Swelling
An enlargement that can change the battery or surrounding device shape; it needs manufacturer attention.
System configuration
The actual arrangement of equipment, distribution, controls and served areas at a stated time.
System preparation
The actual provider’s defined work and intended state for a particular building system.
Tamper indication
A product feature showing whether its intended safety arrangement has been disturbed; it is not a complete service assessment.
Tank check valve
The named example’s one-way tank-inlet function that helps retain pressure after pumping stops.
Tank draw-off
The useful water delivered between specified control conditions; different from the vessel’s total volume.
Tank operating permit
A permission category used by the relevant authority for defined storage equipment; it is distinct from permission for installation or alteration work.
Tankless heater
An appliance that adds heat to water passing through it within its documented operating capability.
Targeted assessment
Professional work selected to answer a defined technical question rather than assess every aspect of a property.
Targeted repair
Work directed at a defined location or mechanism within stated scope.
Tariff
The applicable written utility charging rules for a particular account and service arrangement.
Tax account balance
An account position as of its statement date, distinct from the original charge.
Tax charge
The amount charged for the period identified on the actual bill.
Taxation assessment
An estimate of property value for the applicable taxation system and reference dates.
Temperature feedback
Information from an actual sensor location used by a documented control.
Temperature history
Existing dated temperature observations with their locations, units and gaps, rather than a complete assurance about each stored item's prior condition.
Temperature rise
The difference between incoming and intended outgoing water temperatures.
Temperature set point
The control’s intended setting, separate from a measured temperature at a named fixture.
Tenancy
The relationship governing occupation under the actual agreement and applicable law.
Tendon
The steel and associated components of the prestressing assembly, rather than a synonym for every bar in a slab.
Termination
The outdoor end of the connected exhaust route, such as its identified wall or roof hood.
The interface connecting a conductor to equipment, assessed for its actual materials, condition and application.
The identified end of a route, such as the outside hood of a vented dryer.
Test panel
The defined group of analytes included in a laboratory request.
Thermal break
A layer intended to limit heat transfer at a particular part of an assembly; not automatically a complete insulation strategy.
Thermal bridge
A route with greater heat transfer than the surrounding insulated assembly.
A relatively conductive connection that carries heat across an insulating arrangement.
A path through an enclosure that transfers heat differently from neighbouring insulated construction.
Thermal expansion
A material’s dimensional change with temperature; different materials can behave differently at an interface.
Thermal resistance
Resistance to heat flow under the stated test or assembly conditions; a material value is not whole-house performance.
Thermal response
The change in room or assembly conditions over time, influenced by stored energy, delivery, losses and controls.
How an assembly’s temperature changes over time under stated heat input and surrounding conditions.
Thermal source
Where a described system obtains or rejects heat.
Thermostatic mixing valve
A device that combines hot and cold water to limit delivered temperature along its intended route.
Three-way control
An arrangement for controlling lights from two locations. Which location can dim depends on the documented devices.
Through-floor lift
A device category relating travel to a floor opening rather than an assumed continuous hoistway; identify the actual model and protection.
Through-wall flashing
A connected detail collecting water behind masonry and directing it outward.
Timber frame
A structure of substantial members; infill enclosure has its own assembly.
Time-based maintenance reminder
A care reminder based on running time or a schedule, rather than a direct check of the bag or filter’s current condition.
Timing gap
Funds are available later than the date they are required.
Tip-over
An object becoming unstable, distinct from whether it previously stood without incident.
Titled parking unit
A parking interest recorded through the applicable title system; its link to a residential unit needs actual records.
Toe kick
The recessed base finish; in the named system it is separate from supporting legs.
Top-up
A designed backup supply to a nonpotable system when collected water is insufficient.
Total lead
The lead quantity addressed by Health Canada’s drinking-water guideline, considered with the applicable collection and laboratory method.
Total Stop System
The named Sun Joe model’s automatic motor-stop function related to its flow/control state; not a universal design.
Total VOC
A method-dependent combined result that does not independently identify every compound or establish its health risk.
Traction
The job of moving the machine along the surface.
Traction drive
The function that moves the machine along the ground, separate from the snow-handling drive.
Trade permit
A locally applicable approval process for a defined discipline such as electrical or plumbing work, distinct from other project approvals.
Trade scope
A defined electrical, heating, plumbing or other specialist engagement.
Traffic membrane
A named membrane designed for both pedestrian use and waterproofing under its particular product and project conditions.
Transfer route
The path allowing air to move between an occupied room and the rest of the air-distribution system.
Transition record
The available identity, location and assessment of a connection between different components or materials.
Trap
A curved drain part that retains a water seal to help keep sewer gases out of the room.
Trap seal
The water retained in a trap to form a barrier against gas passage while allowing drainage.
Water retained in a trap to provide a barrier between the room and gases in the drainage system.
Tread
The horizontal surface stepped on; its finish is different from the underlying supporting construction.
Treatment area
The documented area and components performing the downstream treatment function for the particular system.
Treatment scope
The locations, items, methods and exclusions in the actual pest-service assignment.
Treatment train
The connected sequence of treatment stages, each with its own function and operating requirements.
Treatment verification
Evidence that the installed process meets its stated target under relevant operating conditions.
Target-specific evidence comparing the water entering a unit and its treated water under identified conditions.
Tree protection zone
A site-specific area and restrictions defined for the actual tree and project by the appropriate professional.
Tree risk assessment
A scoped professional consideration of possible failure and what could be affected; distinct from a general health observation.
Trigger gun
The assembled control for ordinary discharge through the lance and nozzle.
Trigger rate
For the fixed-payment variable disclosure described by FCAC, the annual rate at which the payment no longer covers interest for the period; contract responses require separate review.
Tube
A ceramic sleeve protecting a conductor where it passes through a timber member.
Two-stage snowblower
An arrangement with a gathering auger and separate throwing impeller; the actual model establishes construction.
Unassessed layer
A layer that the available assessment did not identify. It still needs an answer if your work could affect it.
Unbonded tendon
A tendon whose steel is not bonded to the surrounding concrete along its length; protection and anchorage still matter.
Uncoupling and crack-isolation membrane
A named intermediate component with a manufacturer-defined movement/crack-isolation role in a tile system, subject to its actual substrate and movement limits; it does not replace supporting construction.
Uncoupling membrane
A specified assembly component intended to manage movement between substrate and finish; a separate retained cable makes heat in the illustrated heated example.
Uninspected remainder
Relevant route outside the actual reported assessment, with neither a passed condition nor a defect established.
Unintended washer siphoning
An installation-related drain-path effect discussed in manufacturer instructions that can remove water the wash process was intended to retain; a low visible level alone does not establish it.
Unit allocation
The documented basis for assigning a contribution to a unit, interpreted under the applicable framework.
Unloader
The named manual’s separate pressure-control function; not an owner adjustment instruction.
Unobstructed opening
The clear space remaining in the relevant normal open position, distinct from glass, frame and rough-opening dimensions.
Unresolved question
An important question for which the available information still does not supply the answer needed for the decision.
Unresolved work allowance
An invented or provisional planning amount for an unanswered task; it is neither a diagnosis nor a contractor quotation.
Upgrade forecast
An estimated result for proposed work, with its author and assumptions. It does not record completed work or an achieved saving.
UPS
Equipment that can supply a stated connected load from stored energy during supported input interruptions.
Upstream
On the supply side of a component, such as the gas entering a regulator.
Usable advance
The amount identified as available for completion after any actual documented treatment of charges or deductions.
Usable bulk storage
Water available within the documented usable range of a separate storage component, with refill and onward-delivery dependencies retained.
Utility-tree scope
Work coordinated with the relevant utility and suitably qualified provider; not ordinary owner pruning.
UV disinfection
A treatment step exposing passing water to ultraviolet light to affect microorganisms’ ability to reproduce.
Vacant possession
A transaction and legal question about availability, requiring the actual agreement and local advice.
Valuation date
The market reference date used by the particular assessment system.
Vaporization
Liquid changing into gas. Container conditions affect how readily stored propane can supply vapour.
Vapour
The gas form of a substance that can also be present as a liquid; in this lesson, propane gas.
Vapour control
A material or layer’s role in limiting water vapour moving through materials, rather than air carrying it through an opening.
Vapour diffusion
Water-vapour movement through materials, distinct from vapour carried with moving air.
Variable-speed drive
Matched motor-control equipment that can change pump motor speed in response to the system’s demand signal.
Vehicle carry-in
Snow, slush, water or residue transported inside on a vehicle; a possible route to compare with the ordinary arrival history.
Vent fan
In the named over-range example, a fan serving cooking vapours from the surface below.
Vented attic
A roof space with an intended outside-air route, distinct from unwanted room air leaking through the ceiling.
Vented dryer
An identified appliance that sends drying exhaust through a connected route outdoors.
Ventilation
Movement of air into and out of a home, distinct from adding heat or merely circulating room air.
Ventilation route
An intended path for outdoor supply or indoor exhaust, distinct from simply circulating room air.
Ventilation slots
Openings that must remain clear as the manufacturer requires.
Ventless heat-pump dryer
A purpose-built arrangement using a refrigeration system to dry and recycle air, with model-specific care and collected-water handling.
Verification scope
The work area, conditions and methods covered by a completion or follow-up check.
Visual inspection
An assessment of accessible observable parts under the agreed method and applicable scope; it does not expose every concealed condition.
Volumetric module
A three-dimensional factory-made building portion transported and joined on site; its finish and certified scope depend on the actual system.
Walking roof
An outdoor walking area that also roofs enclosed space. The name describes the geometry, not ownership or an approved assembly.
Warning interconnection
A compatible arrangement in which activation of one relevant alarm causes other specified devices to sound.
Warranty commencement
The applicable start of coverage, established by the relevant warranty documents and rules rather than an assumed move-in date.
Warranty insurance
An actual issued policy with its own scope and process.
Washer discharge hose
The model-specific water-out route between the appliance and its identified receiving drain arrangement, with routing and retention governed by matching instructions and local requirements.
Washer drain pump
The identified appliance function that moves used water through its discharge route; it does not establish the capacity or condition of the receiving building drain.
Washer inlet valve
The appliance component managing incoming water for its fill function; an off control is not the same as isolating the upstream household supply.
Washer interface assessment
A stated examination of the actual appliance, water connections and receiving-drain relationship, with findings, methods, conditions and exclusions kept distinct.
Washer supply connection
The identified household-water valve, inlet hose, fittings and appliance inlet interface that delivers water to the machine; it differs from wastewater discharge.
Water balance
The measured water-chemistry conditions managed under the appropriate care programme, rather than a judgement from appearance.
Water destination
The applicable bucket, gravity-drain or pump-assisted destination for condensed liquid. The actual model and installation determine its route.
Water service
The incoming pipe connection bringing supplied water to the property. Confirm its ownership and operating boundaries with the local provider.
Water supply branches
Pipes inside the building that distribute water to taps, fixtures and appliances.
Water vapour
Invisible water in air, different from the liquid droplets visible in a pan or bucket.
Water in its gaseous form, distinct from liquid droplets.
Water-entry route
The actual path by which water reaches the affected location, requiring evidence beyond a stain.
Water-fed baseboard
A room heater receiving heat through water from another source; its long cover can resemble an electric heater.
Water-flow alarm role
An identified interface that can turn a sustained sprinkler-water flow condition into an alarm, distinct from the head’s thermal opening.
Water-hammer arrestor
An engineered device with a compressible cushion separated from the water; suitability depends on the actual product and system.
Water-removal capacity
A rated water amount over a stated period under the applicable rating conditions; not a promised amount for this home.
Water-vapour control
Management of water vapour moving through an assembly; it differs from control of moving air and liquid rain.
Waterproofing
The water-resisting boundary protecting the assembly below.
Watts and lumens
Watts describe electrical power. Lumens describe light output. Neither quantity alone establishes control compatibility or safety.
Wearing surface
The traffic-exposed top of the floor; it does not by itself describe the whole slab or supporting arrangement.
The top surface that people or vehicles use. Its appearance does not identify everything supporting it.
Weep opening
An intended outlet from an identified wall drainage detail.
Well drawdown
A change in well water level during pumping, interpreted with the test’s rate, duration and recovery information.
Well water-level drawdown
The change in well water level during pumping, measured as a length relative to its reference; distinct from a tank’s released-water volume.
Wet-area assembly
The connected finish, support, water-control and drainage arrangement serving an area intended to receive water.
Wet-pipe arrangement
The named system context in which water is present in piping before operation; its presence in a particular property still requires identification.
Whole route
Approach, pauses, doors, turns and destination activity considered together.
Whole-product U-factor
A heat-transfer value including the glazing, edges and frame rather than the centre glass alone.
Whole-property inventory
A list of the buildings, installed systems and site features that need to be considered when agreeing the actual inspection scope.
Wi-Fi
A local wireless radio connection; separate from the outside internet service.
Winder
A tapered step in a turning stair; tread surface varies across its width.
Window well
An exterior structure holding back surrounding ground at a below-grade window.
Winterization scope
The exact taps, equipment and supplies covered by seasonal preparation, including isolation, remaining water dependencies and restart instructions.
Work scope
The actual tasks, materials, interfaces, assumptions and exclusions of a proposal.
Work zone
The actual restricted project area and interfaces defined by the appropriate work plan.
Worktop seam
The joint between surface pieces, with material, geometry and support context.
Wrap
A water-control layer behind the cladding; a real system may use a sheet membrane or a specified coating.
Zeolite drying example
The identified model’s mineral moisture-uptake and heat-release relationship with an internal air route, not a feature inferred for every dishwasher.
Zone valve
The valve controlling water into a particular irrigation branch.
No terms match. Try a broader word or open the guide library.